Ricoh FT1208, 1008 manual Condition Cause Remedy See

Page 54

Condition

Cause

Remedy

 

See

 

Page

 

 

 

 

 

 

 

 

 

 

 

 

Power cord is not properly

Plug it in firmly.

-

 

plugged into the outlet.

 

 

 

 

 

 

 

 

 

 

Nothing happens

 

Check that the both ends of

 

when the switch is

 

the top unit are securely

 

turned on.

Top unit is not completely

closed. If not, close the top

15

 

closed.

unit firmly by pressing the

 

 

 

marked

position.

 

 

 

 

 

 

 

PE is displayed on

Paper cassette is empty.

Load paper.

 

18

the copy counter.

 

 

 

 

 

 

 

 

 

 

 

 

L&I is blinking.

Toner has nearly run out

Replace

toner

cassette.

42

 

 

 

 

 

 

L&l stays on.

Toner has run out.

Replace

toner

cassette.

42

 

 

 

 

& stays on.

A misfeed has occurred.

Clear misfed paper.

59

 

 

 

 

 

 

The copier has

 

 

 

 

 

entered Auto-off

The copier has shifted to the

Press any key to re-activate

 

mode (30 minutes

21

after a copy was

Auto-off function.

the copier.

 

made or a key was

 

 

 

 

 

pressed).

 

 

 

 

 

 

 

 

 

 

 

Copies have white

 

 

 

 

 

streaks.

Corona wires are dirty.

Clean the corona wires.

45

 

Copy image

 

 

 

 

 

density is uneven.

 

 

 

 

 

 

 

 

 

t’ i is displayed on

The copier is overheated.

Wait for a while until the

 

copier cools down and t’ I is

48

the copy counter.

 

no longer displayed.

 

 

 

 

 

 

 

 

 

 

ATTENTION: If the error code (E ..) appears, turn off the main switch, then turn it on. If the error code disappears, the copier will function. If the error code appears again, turn off the main switch and immediately call your service personnel.

56

Image 54
Contents Ricoh FT1008/1208 For details, see pages Essential Symbols Page Power cord Main Switch Guide Plates Qpe1&2 Press to reduce/enlarge copies in preset ratios. See 20-21 Clearing Misfeeds Auto-off mode -for automatically Saving powerPage Page Remove the toner cassette from the vinyl bag Adjusting the paper length Adjusting the paper widthPage Confirm that the copy tray is securely in place Power Connection Turning Copier OnAuto-off mode for automatically saving power Copier Location Bypass Feed Copying Alignment of Originals ++ +o Align the center of the original to the arrow mark Transparencies LetterheadTwo-sided copies Page Page Page Press the Start key to make the first copy Page Page Page User Tool Adjustable item See Number Page Adjusting values/modes Auto image density levelUser modeDarker-side manual image density level User mode Auto reset durationUser mode Page Maintaining the Copier Copy YieldKeep the vinyl bag for repacking Page Platen Cover P y Tray Bypass Feed Page Keep this tool inside the copier Attension Make sure to press the marked position Page Page Page Page Put the toner cassette in a vinyl bag Put the copier in the cardboard box When Pz appears on the copy counter When & stays onCondition Cause Remedy See Condition Cause Remedy PZe Page When PE appears on the copy counter When & is lit Specifications Copy Process ConfigurationCopy Paper Weight OriginalsDimensions Page Page Page EE@rnm~