Samsung SCX-1000 Series manual Onnecting Printer Cable, Parallel cable connection

Page 11

01-M30UK(1-6 to 2-11) 5/22/00 3:19 PM Page 4

Chapter 2

Connecting

the Printer Cable

The SCX-1000 Series printer has two interfaces for wide connectivity; parallel and USB. If you are running Windows 98 or higher and your computer is equipped with a USB port, see page 2-6 for connection.

Parallel cable connection

To prevent malfunction, it is strongly recommend that you use the supplied parallel cable with the printer. If you need to purchase another cable, ensure that it is complies to IEEE- 1284.

1 Check that both the printer and the computer are powered off and disconnected from the power point.

2 Plug one end of the parallel cable into the connector on the rear of the printer.

Push the metal clips down to fit inside the notches on the cable plug.

Plug the other end of the cable into the appropriate parallel connector on your computer and fasten it tight.

2-4Setting Up Your Printer

Setting Up Your Printer 2-5

Image 11

Contents 00-M30UKCover 5/22/00 408 PM Safety Precautions Introduction Printing Multipage on a Single Print Media10-10 10-110-2 10-5Overview IntroductionYou can easily scan documents and photographs About This GuideUSB Port Manual Feeder Printer ComponentsMemo Setting Up Your PrinterUser’s Guide CD-ROMs SmarThru 2 Guide Power Cord Parallel CableParallel cable connection Onnecting Printer CableUSB cable connection Connecting the Printer CableLoading Paper into the Input Tray Insert cartridges Press Enter/SelectDisplay Press Enter/Select Left CARTRIDGE? appearsRight CARTRIDGE? appears Like this Cartridge type Part numberTo change the alignment value Has printed, the display looksSamsung SmarThru 2 provides you with Printer software printer driverSmarThru 2 program Software Requirements Hardware RequirementsTypical recommended Type the mail server address and then click the Next button When you have completed, click FinishFollow the instructions on the screen To uninstall the printer driver, proceed as followsTo uninstall the SmarThru 2 program, proceed as follows CongratulationsClick Copy all disk images Use them instead of the CD-ROM to install the softwareInstalling Software from Diskette Using the Control PanelButton Function Printer. Look for the following buttons and their functionsAttendance Message Print MediaStatus Message When you choose print media, consider the following Media DimensionUse only undamaged paper Not supported paper typesSmoothness and colour of the paper For best print quality, use inkjet paperPrinting Tasks Following procedure describes the general steps required Setting Your Default PrinterDefault printer, follow the procedures as described below Click Printer and select Set as DefaultSelect Start Programs Samsung SCX-1000 Series Using the Status TabUsing the Options Tab Starting the SCX-1000 Series Control ProgramEach property that the printer provides Using the Cartridges Tab1Selectbar. Start Settings Printers from the Windows task This tab allows you to choose cartridge optionsDocument/Quality Tab Paper TabImage Making a CopyAdvanced Tab HalftoneNumber appears on To select the new settingTo cancel a copy in progress press the Stop/Restore button Press ˆ or ¤ until the desiredTo change Copy Size To change Copy ResolutionTo change Copy Contrast Either Enter/Select or Stop/RestorePress the Special Copy SCX-1000S only Smart Media FunctionCard care and Storage Press Enter/Select when SDC50002.JPG appearsInserting and Removing Cards Selecting the file stored on the Smart Media CardImages and make copies without a direct link to a PC Press ˆ or ¤ to select the print modeYou can print images captured on digital cameras To delete a image file from the Smart Media card Changing Printer Setting Paper Type appears Maintaining Your Printer Page, complete the following steps To install the print cartridgeTo remove the print cartridge Alignment test page. If you need to print an alignment testTo wipe the printheads To clean the printheadsTo clean the Scanner Bed Clean the printheadsPrinter prints the Help list Not satisfactoryRemove the print cartridge from the printer If you need help, see ‘To Remove the Print Cartridge’ onTo restore factory defaults TroubleshootingLift the Output Tray Paper jams while the printer is feedingPaper jams while printing Pull the Input Tray completely out of the printerTips for Avoiding Paper Jams Smart Media messages Stop/Restore buttonPress the Enter/Select Selecting the Default Printer Change the Print Quality to High or Normal When the current job is completed, try again Mode because a lot of memory is required toComputer to ECP mode through Bios setting. It How to set BIOS, refer to the document of yourAnyPage Lite does not offer the scan feature Brightness or too low resolution. AdjustAccuracy. Do not forget to set the switch back to Printer in draft modePecifications SpecificationPrinter Stafford Park 12, Telford Shropshire TF3 3BJ Replacing the Fitted PlugIndex Twain UI