Samsung SCX-1000 Series manual Hardware Requirements, Software Requirements

Page 18

02-M30UK(2-12 to 2-21) 5/22/00 3:41 PM Page 18

Continued

Installing the Printer Software

Hardware Requirements

To install and run the Printer Software you must have the following hardware configuration:

●120MB of available Hard disk space

●Pentium 133 or better

●32MB of RAM or more

Software Requirements

To install and run the Printer Software you must have the following software configuration.

●Windows 95 OSR2

●Windows 98 or Windows 98 SE

●If you are installing the software onto a Windows NT 4 Workstation, you must have installed Service Pack 3 or higher

●Internet Explorer 4.01 or later

1 Installing the printer software

1 Make sure the printer is plugged in and connected to your computer.

2 Start Windows.

3 When the New Hardware Found message appears, click the Cancel button.

4 Insert the Setup CD-ROM into the CD-ROM drive. The Model Selection window should appear automatically.

If the installation does not start automatically, do the following:

a)Click Start ➝ Run from the Windows task bar.

b)Type e:\Setup.exe (substitute your CD-ROM drive letter for the ‘e’) on the command line, then click the OK button.

5 Select the printer model which is connected to your computer.

6 Select the language you want to use .

If you do not have a CD-ROM drive, you can copy the Setup program onto floppy diskettes.

For more information see ‘Making Installation Diskettes’ page 2-26.

Chapter 2

2-18Setting up Your Printer

Setting up Your Printer 2-19

Image 18

Contents 00-M30UKCover 5/22/00 408 PM Safety Precautions Introduction Print Media Printing Multipage on a Single10-5 10-110-2 10-10Introduction OverviewAbout This Guide You can easily scan documents and photographsPrinter Components USB Port Manual FeederSetting Up Your Printer MemoPower Cord Parallel Cable User’s Guide CD-ROMs SmarThru 2 GuideOnnecting Printer Cable Parallel cable connectionConnecting the Printer Cable USB cable connectionLoading Paper into the Input Tray Press Enter/Select Insert cartridgesPress Enter/Select Left CARTRIDGE? appears Right CARTRIDGE? appearsDisplay Has printed, the display looks Cartridge type Part numberTo change the alignment value Like thisPrinter software printer driver SmarThru 2 programSamsung SmarThru 2 provides you with Hardware Requirements Software RequirementsTypical recommended When you have completed, click Finish Type the mail server address and then click the Next buttonCongratulations To uninstall the printer driver, proceed as followsTo uninstall the SmarThru 2 program, proceed as follows Follow the instructions on the screenUse them instead of the CD-ROM to install the software Click Copy all disk imagesUsing the Control Panel Installing Software from DiskettePrinter. Look for the following buttons and their functions Button FunctionPrint Media Status MessageAttendance Message Media Dimension When you choose print media, consider the followingFor best print quality, use inkjet paper Not supported paper typesSmoothness and colour of the paper Use only undamaged paperPrinting Tasks Click Printer and select Set as Default Setting Your Default PrinterDefault printer, follow the procedures as described below Following procedure describes the general steps requiredStarting the SCX-1000 Series Control Program Using the Status TabUsing the Options Tab Select Start Programs Samsung SCX-1000 SeriesThis tab allows you to choose cartridge options Using the Cartridges Tab1Selectbar. Start Settings Printers from the Windows task Each property that the printer providesPaper Tab Document/Quality TabHalftone Making a CopyAdvanced Tab ImagePress ˆ or ¤ until the desired To select the new settingTo cancel a copy in progress press the Stop/Restore button Number appears onTo change Copy Resolution To change Copy ContrastTo change Copy Size Stop/Restore Either Enter/Select orPress the Special Copy Smart Media Function SCX-1000S onlySelecting the file stored on the Smart Media Card Press Enter/Select when SDC50002.JPG appearsInserting and Removing Cards Card care and StoragePress ˆ or ¤ to select the print mode You can print images captured on digital camerasImages and make copies without a direct link to a PC To delete a image file from the Smart Media card Changing Printer Setting Paper Type appears Maintaining Your Printer Alignment test page. If you need to print an alignment test To install the print cartridgeTo remove the print cartridge Page, complete the following stepsClean the printheads To clean the printheadsTo clean the Scanner Bed To wipe the printheadsIf you need help, see ‘To Remove the Print Cartridge’ on Not satisfactoryRemove the print cartridge from the printer Printer prints the Help listTroubleshooting To restore factory defaultsPull the Input Tray completely out of the printer Paper jams while the printer is feedingPaper jams while printing Lift the Output TrayTips for Avoiding Paper Jams Stop/Restore button Smart Media messagesPress the Enter/Select Selecting the Default Printer Change the Print Quality to High or Normal How to set BIOS, refer to the document of your Mode because a lot of memory is required toComputer to ECP mode through Bios setting. It When the current job is completed, try againPrinter in draft mode Brightness or too low resolution. AdjustAccuracy. Do not forget to set the switch back to AnyPage Lite does not offer the scan featureSpecification PecificationsPrinter Replacing the Fitted Plug Stafford Park 12, Telford Shropshire TF3 3BJIndex Twain UI