Samsung SCX-1000 Series To clean the printheads, To wipe the printheads, To clean the Scanner Bed

Page 46
cleaning direction

09-M30UK(9-2 to 10-3) 5/22/00 3:30 PM Page 4

Chapter 9

Cleaning Your Printer

 

The following sections take you through the process of cleaning

 

the print cartridge printheads.

 

To clean the printheads

To wipe the printheads

Run CLEAN CAR. to clean the printheads.

A test line prints so that you can see if the cleaning process was

successful.

Clean the printheads:

When you suspect the printheads are clogged.

When characters are not printing completely.

1)

Remove the print cartridge from the printer.

 

If you need help, see ‘To Remove the Print

 

Cartridge’ on page 9-2.

2)

Use a clean, damp cloth to gently wipe

 

the entire copper contact area and the

 

printheads as shown.

Copper Contact Area

1)

Press the Setup button until

 

CARTRIDGE appears in the display.

2)

Press ˆ or ¤ until CLEAN CAR.

[CARTRIDGE] ¤ CHANGE CAR.

[CARTRIDGE]

3) Allow the copper contact area to dry.

Printhead

When cleaning the colour print cartridge wipe the printheads in one direction

 

appears in the second row of the

 

display.

3)

Press the Enter/Select button.

 

The printer prints the printheads

 

cleaning test page.

4)

If the printheads cleaning test

 

page still contains broken lines,

 

see ‘To Wipe the

 

printheads’ on page 9-5.

¤CLEAN CAR.

PRINTING ■■■

4)Reinstall the print cartridges.

If you need help, see ‘Installing the Print Cartridges’ on page 2-10.

5)Close the Scanner Bed.

6)Repeat the cleaning printheads test.

If you need help, see ‘To clean the printheads’ on page 9-4.

7)If the cleaning printheads test page still contains broken lines, see ‘Cleaning the Print Cartridge Carrier Contacts’ on page 9-6.

so the colours do not mix.

To clean the Scanner Bed

2)

Lift the Printer Top Cover.

Chapter

The printer slows down copying and scanning performance if the

 

Scanner Bed is dirty. Keep the bed clean.

 

1)

Unplug the power cord.

 

The printer returns to Ready Mode after the test page.

3) Use a clean, damp cloth to

Scanner

9

 

Bed

 

clean the bed.

 

 

9-4Troubleshooting

Maintaining Your Printer 9-5

Image 46
Contents 00-M30UKCover 5/22/00 408 PM Safety Precautions Introduction Print Media Printing Multipage on a Single10-5 10-110-2 10-10Introduction OverviewAbout This Guide You can easily scan documents and photographsPrinter Components USB Port Manual FeederSetting Up Your Printer MemoPower Cord Parallel Cable User’s Guide CD-ROMs SmarThru 2 GuideOnnecting Printer Cable Parallel cable connectionConnecting the Printer Cable USB cable connectionLoading Paper into the Input Tray Press Enter/Select Insert cartridgesRight CARTRIDGE? appears Press Enter/Select Left CARTRIDGE? appearsDisplay Has printed, the display looks Cartridge type Part numberTo change the alignment value Like thisSmarThru 2 program Printer software printer driverSamsung SmarThru 2 provides you with Hardware Requirements Software RequirementsTypical recommended When you have completed, click Finish Type the mail server address and then click the Next buttonCongratulations To uninstall the printer driver, proceed as followsTo uninstall the SmarThru 2 program, proceed as follows Follow the instructions on the screenUse them instead of the CD-ROM to install the software Click Copy all disk imagesUsing the Control Panel Installing Software from DiskettePrinter. Look for the following buttons and their functions Button FunctionStatus Message Print MediaAttendance Message Media Dimension When you choose print media, consider the followingFor best print quality, use inkjet paper Not supported paper typesSmoothness and colour of the paper Use only undamaged paperPrinting Tasks Click Printer and select Set as Default Setting Your Default PrinterDefault printer, follow the procedures as described below Following procedure describes the general steps requiredStarting the SCX-1000 Series Control Program Using the Status TabUsing the Options Tab Select Start Programs Samsung SCX-1000 SeriesThis tab allows you to choose cartridge options Using the Cartridges Tab1Selectbar. Start Settings Printers from the Windows task Each property that the printer providesPaper Tab Document/Quality TabHalftone Making a CopyAdvanced Tab ImagePress ˆ or ¤ until the desired To select the new settingTo cancel a copy in progress press the Stop/Restore button Number appears onTo change Copy Contrast To change Copy ResolutionTo change Copy Size Stop/Restore Either Enter/Select orPress the Special Copy Smart Media Function SCX-1000S onlySelecting the file stored on the Smart Media Card Press Enter/Select when SDC50002.JPG appearsInserting and Removing Cards Card care and StorageYou can print images captured on digital cameras Press ˆ or ¤ to select the print modeImages and make copies without a direct link to a PC To delete a image file from the Smart Media card Changing Printer Setting Paper Type appears Maintaining Your Printer Alignment test page. If you need to print an alignment test To install the print cartridgeTo remove the print cartridge Page, complete the following stepsClean the printheads To clean the printheadsTo clean the Scanner Bed To wipe the printheadsIf you need help, see ‘To Remove the Print Cartridge’ on Not satisfactoryRemove the print cartridge from the printer Printer prints the Help listTroubleshooting To restore factory defaultsPull the Input Tray completely out of the printer Paper jams while the printer is feedingPaper jams while printing Lift the Output TrayTips for Avoiding Paper Jams Stop/Restore button Smart Media messagesPress the Enter/Select Selecting the Default Printer Change the Print Quality to High or Normal How to set BIOS, refer to the document of your Mode because a lot of memory is required toComputer to ECP mode through Bios setting. It When the current job is completed, try againPrinter in draft mode Brightness or too low resolution. AdjustAccuracy. Do not forget to set the switch back to AnyPage Lite does not offer the scan featureSpecification PecificationsPrinter Replacing the Fitted Plug Stafford Park 12, Telford Shropshire TF3 3BJIndex Twain UI