Samsung SCX-1000 Series manual Connecting the Printer Cable, USB cable connection

Page 12

01-M30UK(1-6 to 2-11) 5/22/00 3:19 PM Page 6

Continued

Connecting the Printer Cable

To use a USB cable for printing, your computer should be running

Windows 98 or higher and have a USB port.

USB cable connection

The USB and parallel printer cables cannot be connected

simultaneously. You should decide which connection to use and the

best connection to fit your requirement.

1 Make sure that both the printer and computer are turned off.

2 Plug one end of the certified USB cable into the USB port on the printer.

3 Plug the other end into the USB port on the computer.

Chapter 2

Connecting the Power Cord

TheSCX-1000 Series printer has a power range of 110-240V AC.

1 Plug one end of the power cable supplied to the connector on the rear of the printer.

2 Plug the other end into a suitable power point.

The printer indicates and enters the Ready Mode. At this moment, you will hear some of movement inside the printer.

2-6Setting Up Your Printer

Setting Up Your Printer 2-7

Image 12
Contents 00-M30UKCover 5/22/00 408 PM Safety Precautions Introduction Print Media Printing Multipage on a Single10-1 10-210-5 10-10Introduction OverviewAbout This Guide You can easily scan documents and photographsPrinter Components USB Port Manual FeederSetting Up Your Printer MemoPower Cord Parallel Cable User’s Guide CD-ROMs SmarThru 2 GuideOnnecting Printer Cable Parallel cable connectionConnecting the Printer Cable USB cable connectionLoading Paper into the Input Tray Press Enter/Select Insert cartridgesPress Enter/Select Left CARTRIDGE? appears Right CARTRIDGE? appearsDisplay Cartridge type Part number To change the alignment valueHas printed, the display looks Like thisPrinter software printer driver SmarThru 2 programSamsung SmarThru 2 provides you with Hardware Requirements Software RequirementsTypical recommended When you have completed, click Finish Type the mail server address and then click the Next buttonTo uninstall the printer driver, proceed as follows To uninstall the SmarThru 2 program, proceed as followsCongratulations Follow the instructions on the screenUse them instead of the CD-ROM to install the software Click Copy all disk imagesUsing the Control Panel Installing Software from DiskettePrinter. Look for the following buttons and their functions Button FunctionPrint Media Status MessageAttendance Message Media Dimension When you choose print media, consider the followingNot supported paper types Smoothness and colour of the paperFor best print quality, use inkjet paper Use only undamaged paperPrinting Tasks Setting Your Default Printer Default printer, follow the procedures as described belowClick Printer and select Set as Default Following procedure describes the general steps requiredUsing the Status Tab Using the Options TabStarting the SCX-1000 Series Control Program Select Start Programs Samsung SCX-1000 SeriesUsing the Cartridges Tab 1Selectbar. Start Settings Printers from the Windows taskThis tab allows you to choose cartridge options Each property that the printer providesPaper Tab Document/Quality TabMaking a Copy Advanced TabHalftone ImageTo select the new setting To cancel a copy in progress press the Stop/Restore buttonPress ˆ or ¤ until the desired Number appears onTo change Copy Resolution To change Copy ContrastTo change Copy Size Stop/Restore Either Enter/Select orPress the Special Copy Smart Media Function SCX-1000S onlyPress Enter/Select when SDC50002.JPG appears Inserting and Removing CardsSelecting the file stored on the Smart Media Card Card care and StoragePress ˆ or ¤ to select the print mode You can print images captured on digital camerasImages and make copies without a direct link to a PC To delete a image file from the Smart Media card Changing Printer Setting Paper Type appears Maintaining Your Printer To install the print cartridge To remove the print cartridgeAlignment test page. If you need to print an alignment test Page, complete the following stepsTo clean the printheads To clean the Scanner BedClean the printheads To wipe the printheadsNot satisfactory Remove the print cartridge from the printerIf you need help, see ‘To Remove the Print Cartridge’ on Printer prints the Help listTroubleshooting To restore factory defaultsPaper jams while the printer is feeding Paper jams while printingPull the Input Tray completely out of the printer Lift the Output TrayTips for Avoiding Paper Jams Stop/Restore button Smart Media messagesPress the Enter/Select Selecting the Default Printer Change the Print Quality to High or Normal Mode because a lot of memory is required to Computer to ECP mode through Bios setting. ItHow to set BIOS, refer to the document of your When the current job is completed, try againBrightness or too low resolution. Adjust Accuracy. Do not forget to set the switch back toPrinter in draft mode AnyPage Lite does not offer the scan featureSpecification PecificationsPrinter Replacing the Fitted Plug Stafford Park 12, Telford Shropshire TF3 3BJIndex Twain UI