Samsung SCX-1000 Series manual Paper jams while the printer is feeding, Paper jams while printing

Page 49

09-M30UK(9-2 to 10-3) 5/22/00 3:30 PM Page 10

Chapter 10

Clearing Paper Jams

By carefully selecting print media and loading them properly, you should be able to avoid most paper jams.

Paper jams while the printer is feeding

1 Pull the Input Tray completely out of the printer.

Output Tray

Input Tray

2 Lift the Output Tray.

Paper jams while printing

1 Open the Rear Cover by pushing the metal clips at each end of the cover.

2 Pull the paper out gently and slowly.

Chapter 10

3

4

5

Pull the paper up and toward you to remove it.

Press the Stop/Restore button. The error message disappears.

Replace the Input Tray and lower the Output Tray.

REMOVE PAPER JAM

THEN PRESS STOP

3 Push on the Rear Cover until it snaps into place.

4 Press the Stop/Restore button. The error message disappears.

REMOVE PAPER JAM

THEN PRESS STOP

●If you cannot get a firm grasp on the jammed paper, it may be easier to remove it from the Rear Cover. See ‘Paper jams while printing’ on page

10-3 for more information.

10-2Troubleshooting

Troubleshooting 10-3

Image 49

Contents 00-M30UKCover 5/22/00 408 PM Safety Precautions Introduction Printing Multipage on a Single Print Media10-2 10-110-5 10-10Overview IntroductionYou can easily scan documents and photographs About This GuideUSB Port Manual Feeder Printer ComponentsMemo Setting Up Your PrinterUser’s Guide CD-ROMs SmarThru 2 Guide Power Cord Parallel CableParallel cable connection Onnecting Printer CableUSB cable connection Connecting the Printer CableLoading Paper into the Input Tray Insert cartridges Press Enter/SelectRight CARTRIDGE? appears Press Enter/Select Left CARTRIDGE? appearsDisplay To change the alignment value Cartridge type Part numberHas printed, the display looks Like thisSmarThru 2 program Printer software printer driverSamsung SmarThru 2 provides you with Software Requirements Hardware RequirementsTypical recommended Type the mail server address and then click the Next button When you have completed, click FinishTo uninstall the SmarThru 2 program, proceed as follows To uninstall the printer driver, proceed as followsCongratulations Follow the instructions on the screenClick Copy all disk images Use them instead of the CD-ROM to install the softwareInstalling Software from Diskette Using the Control PanelButton Function Printer. Look for the following buttons and their functionsStatus Message Print MediaAttendance Message When you choose print media, consider the following Media DimensionSmoothness and colour of the paper Not supported paper typesFor best print quality, use inkjet paper Use only undamaged paperPrinting Tasks Default printer, follow the procedures as described below Setting Your Default PrinterClick Printer and select Set as Default Following procedure describes the general steps requiredUsing the Options Tab Using the Status TabStarting the SCX-1000 Series Control Program Select Start Programs Samsung SCX-1000 Series1Selectbar. Start Settings Printers from the Windows task Using the Cartridges TabThis tab allows you to choose cartridge options Each property that the printer providesDocument/Quality Tab Paper TabAdvanced Tab Making a CopyHalftone ImageTo cancel a copy in progress press the Stop/Restore button To select the new settingPress ˆ or ¤ until the desired Number appears onTo change Copy Contrast To change Copy ResolutionTo change Copy Size Either Enter/Select or Stop/RestorePress the Special Copy SCX-1000S only Smart Media FunctionInserting and Removing Cards Press Enter/Select when SDC50002.JPG appearsSelecting the file stored on the Smart Media Card Card care and StorageYou can print images captured on digital cameras Press ˆ or ¤ to select the print modeImages and make copies without a direct link to a PC To delete a image file from the Smart Media card Changing Printer Setting Paper Type appears Maintaining Your Printer To remove the print cartridge To install the print cartridgeAlignment test page. If you need to print an alignment test Page, complete the following stepsTo clean the Scanner Bed To clean the printheadsClean the printheads To wipe the printheadsRemove the print cartridge from the printer Not satisfactoryIf you need help, see ‘To Remove the Print Cartridge’ on Printer prints the Help listTo restore factory defaults TroubleshootingPaper jams while printing Paper jams while the printer is feedingPull the Input Tray completely out of the printer Lift the Output TrayTips for Avoiding Paper Jams Smart Media messages Stop/Restore buttonPress the Enter/Select Selecting the Default Printer Change the Print Quality to High or Normal Computer to ECP mode through Bios setting. It Mode because a lot of memory is required toHow to set BIOS, refer to the document of your When the current job is completed, try againAccuracy. Do not forget to set the switch back to Brightness or too low resolution. AdjustPrinter in draft mode AnyPage Lite does not offer the scan featurePecifications SpecificationPrinter Stafford Park 12, Telford Shropshire TF3 3BJ Replacing the Fitted PlugIndex Twain UI