Samsung M9T manual Environmental Specifications, Linear Shock 1/2 sine pulse, Rotational Shock

Page 16

SPECIFICATIONS

3.6Environmental Specifications

Table 3-6: Environmental Specifications

DESCRIPTION			ST1500LM006 , ST1500LM007 &			ST2000LM003, ST2000LM004 &
			ST1500LM010			ST2000LM006
Ambient Temperature
			(Drive temperature measured on position of figure 3-1 on page 11,
Operating			should be max 65C in range of 0°C -60°C, specified operation temperature.)
Operating
Non-operating				0°C ~ 60°C
Non-operating				-40°C ~ 70°C
Max. gradient				-40°C ~ 70°C
Max. gradient				20°C / 20%/hr
				20°C / 20%/hr
(Temperature/Humidity)

Relative Humidity (non condensing)
Operation					5~90 %
Non-operation					5~95 %
Maximum wet bulb temperature
Operating					30°C
Non-operating					40°C
Altitude (relative to sea level)
Operating				-304.8 m to 3,048 m
Non-operating				-304.8 m to 12,192 m
Vibration
Operating :
	10-500 Hz, Random				1.5 Grms
Non-operating :
	10-500 Hz, Random				5.85 Grms

Linear Shock (1/2 sine pulse)
Operating		2.0 ms			300G
Non-operating		1.0 ms			900G
Rotational Shock
Operating		2.0 ms		3K rad/sec 2
Operating		2.0 ms
Non-operating		2.0 ms		30K rad/sec 2
Non-operating		2.0 ms
Acoustic Noise
(Typical Sound Power)
Idle					2.5 Bels
Seek					2.7 Bels


	Spinpoint M9T Product Manual REV 1.0				10

Image 16

Contents M9T Product Manual Page Table of Contents Iii Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables User Definition ScopeManual Organization Sata ReferenceDescription IntroductionKey Features Standards and Regulations Hardware RequirementsSpecifications Specification SummaryPhysical Specifications Logical ConfigurationsPerformance Specifications Power consumption Power consumptionPower Requirements RatedEnvironmental Specifications Environmental SpecificationsLinear Shock 1/2 sine pulse Rotational ShockReliability Specifications Installation Space RequirementsUnpacking Instructions MountingMounting Dimensions OrientationVentilation Cable ConnectorsSata Connectivity Computer mainboard or Serial ATA host adapter Power ManagementSATA-Bus Interface Connector HDD Power, Sata Interface, and Factory Jumper ConnectorDrive Installation DC Power Connector and SATA-Bus Interface Cable ConnectionsHead / Disk Assembly HDA Base Casting AssemblyDC Spindle Motor Assembly Disk Drive OperationExploded Mechanical View Disk Stack Assembly Head Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration SystemDrive Electronics Digital Signal Process and Interface ControllerDisk Controller DDR Host Interface Control Block Buffer Control BlockDisk Ldpc Control Block Disk Control BlockFrequency Synthesizer Power Management Read/Write ICTime Base Generator Automatic Gain ControlAnalog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIRRead and Write Operations Servo SystemRead Channel Write Channel Firmware FeaturesRead Caching Write Caching Defect Management Automatic Defect AllocationSmart 6 APMSata II Interface Sata TerminologySpinpoint M9T Product Manual REV Physical Interface Signal Summary Signal DescriptionsWhen read When written 2 I/O Register AddressControl Block Register Descriptions RegistersCommand Block Register Descriptions Command Register Ex F7h Device Register Ex F6hStatus Register Ex F7h Sata II Feature SET Device Activity SignalStaggered Spin-up Disable Control Auto-Activate in DMA Setup FISPhy Event Counters Software Settings Preservation Sata Power ManagementCommand Table ATA Command DescriptionsCommand Code Parameters Smart Command Descriptions Check Power Mode E5hDevice Configuration Overlay B1h Download Micro Code 92hDevice Configuration Identify data structure Word Content Execute Device Diagnostics 90h Diagnostic CodesFlush Cache E7h, EAh extended Format Track 50hContent Description Identify Device information=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWNIdle E3h Automatic Standby Timer PeriodsIdle Immediate E1h Initialize Device Parameters 91h NOP 00hRead Buffer E4h Read DMA C8h, 25h extendedRead Log Extended 2Fh Read Multiple Command C4h, 29h extendedRead Long 22h Read Sectors 20h, 24h extended Read Native Max Address F8h, 27h extendedRead Verify Sectors 40h, 41h extended Security Disable Password F6h Recalibrate 10hSecurity Erase Prepare F3h Security Erase Unit F4hSecurity Set Password F1h Security Erase Unit Password Word ContentSecurity Set Password data content Security Freeze Lock F5hSecurity Unlock F2h Set Features EFhSeek 7xh 11 Set Features Register Definitions 12 Transfer Mode ValuesSet Multiple Mode C6h 13 Set Max Feature Register ValuesSet Max Address F9h, 37h extended Sleep E6h14 Smart Feature Registers Values Smart disable operations D9hSmart enable/disable attribute auto-save D2h Smart B0hSmart enable operations D8h Smart execute off-line immediate D4hSmart read data D0h 15 Device Smart Data StructureByte Bit Name Description 16 Smart Attribute Status Flags17 Smart Attribute Data List 18 Off-line Data Collection Status ValuesSelf-test execution status byte 19 Self-test Execution Status ValuesSmart return status DAh Smart read log sector D5hSmart write log sector D6h Standby Immediate E0h Write Buffer E8hWrite DMA CAh, 35h extended Write Fpdma Queued 61hWrite Multiple Command C5h, 39h extended Write Sectors 30h, 34h extendedSpinpoint M9T Product Manual REV Maintenance Precautions MaintenanceGeneral Information HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks