Samsung M9T manual Disk Control Block, Disk Ldpc Control Block, Frequency Synthesizer

Page 32

5.2.2.3The Disk Control Block

The Spinpoint M9T Disk Control block manages the flow of data between the disk and the buffer. It is capable of performing completely automated track read and write operations at a maximum data rate of 800 Mb/s in byte wide NRZ mode. Many flexible features and elements of automation have been incorporated to complement the automation contributed by the Host and Buffer blocks.

The Disk Control block consists of the programmable sequencer (Disk Sequencer), CDR/data split logic, disk FIFO, fault tolerant sync detect logic, and other support logic.

The programmable sequencer contains a 32-by-4 byte programmable SRAM and associated control logic, which is programmed by the user to automatically control all single track format, read, and write operations. From within the sequencer micro program, the Disk Control block can automatically deal with such real time functions as defect skipping, servo burst data splitting, branching on critical buffer status and data compare operations. Once the Disk Sequencer is started, it executes each word in logical order. At the completion of the current instruction word, it either continues to the next instruction, continues to execute some other instruction based upon an internal or external condition having been met, or it stops.

During instruction execution or while stopped, registers can be accessed by the DSP to obtain status information reflecting the Disk Sequencer operations taking place.

5.2.2.4The Disk LDPC Control Block

The Disk Control Block supports a programmable LDPC code. Error detection and correction is handled in the Disk Control block. Automatic on-the-fly hardware correction will take place. Correction is guaranteed to complete before the parity bits of the sector following the sector where the error occurred utilizing standard ATA size sectors.

5.2.2.5Frequency Synthesizer

The frequency synthesizer is a clock frequency generation circuit used to generate a DSP clock, AT disk controller and servo clock from the External Reference clock input.

Spinpoint M9T Product Manual REV 1.0

27

Image 32

Contents M9T Product Manual Page Table of Contents Iii Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Manual Organization ScopeUser Definition Sata ReferenceDescription IntroductionKey Features Standards and Regulations Hardware RequirementsSpecifications Specification SummaryPhysical Specifications Logical ConfigurationsPerformance Specifications Power consumption Power consumptionPower Requirements RatedEnvironmental Specifications Environmental SpecificationsLinear Shock 1/2 sine pulse Rotational ShockReliability Specifications Installation Space RequirementsUnpacking Instructions MountingMounting Dimensions OrientationSata Connectivity Cable ConnectorsVentilation Computer mainboard or Serial ATA host adapter Power ManagementSATA-Bus Interface Connector HDD Power, Sata Interface, and Factory Jumper ConnectorDrive Installation DC Power Connector and SATA-Bus Interface Cable ConnectionsHead / Disk Assembly HDA Base Casting AssemblyDC Spindle Motor Assembly Disk Drive OperationExploded Mechanical View Disk Stack Assembly Head Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration SystemDisk Controller Digital Signal Process and Interface ControllerDrive Electronics DDR Host Interface Control Block Buffer Control BlockFrequency Synthesizer Disk Control BlockDisk Ldpc Control Block Power Management Read/Write ICTime Base Generator Automatic Gain ControlAnalog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIRRead Channel Servo SystemRead and Write Operations Read Caching Firmware FeaturesWrite Channel Write Caching Defect Management Automatic Defect AllocationSmart 6 APMSata II Interface Sata TerminologySpinpoint M9T Product Manual REV Physical Interface Signal Summary Signal DescriptionsWhen read When written 2 I/O Register AddressControl Block Register Descriptions RegistersCommand Block Register Descriptions Command Register Ex F7h Device Register Ex F6hStatus Register Ex F7h Sata II Feature SET Device Activity SignalStaggered Spin-up Disable Control Auto-Activate in DMA Setup FISPhy Event Counters Software Settings Preservation Sata Power ManagementCommand Code Parameters ATA Command DescriptionsCommand Table Smart Command Descriptions Check Power Mode E5hDevice Configuration Overlay B1h Download Micro Code 92hDevice Configuration Identify data structure Word Content Execute Device Diagnostics 90h Diagnostic CodesFlush Cache E7h, EAh extended Format Track 50hContent Description Identify Device information=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWNIdle Immediate E1h Automatic Standby Timer PeriodsIdle E3h Initialize Device Parameters 91h NOP 00hRead Buffer E4h Read DMA C8h, 25h extendedRead Long 22h Read Multiple Command C4h, 29h extendedRead Log Extended 2Fh Read Verify Sectors 40h, 41h extended Read Native Max Address F8h, 27h extendedRead Sectors 20h, 24h extended Security Disable Password F6h Recalibrate 10hSecurity Erase Prepare F3h Security Erase Unit F4hSecurity Set Password F1h Security Erase Unit Password Word ContentSecurity Set Password data content Security Freeze Lock F5hSeek 7xh Set Features EFhSecurity Unlock F2h 11 Set Features Register Definitions 12 Transfer Mode ValuesSet Multiple Mode C6h 13 Set Max Feature Register ValuesSet Max Address F9h, 37h extended Sleep E6h14 Smart Feature Registers Values Smart disable operations D9hSmart enable/disable attribute auto-save D2h Smart B0hSmart enable operations D8h Smart execute off-line immediate D4hSmart read data D0h 15 Device Smart Data StructureByte Bit Name Description 16 Smart Attribute Status Flags17 Smart Attribute Data List 18 Off-line Data Collection Status ValuesSelf-test execution status byte 19 Self-test Execution Status ValuesSmart write log sector D6h Smart read log sector D5hSmart return status DAh Standby Immediate E0h Write Buffer E8hWrite DMA CAh, 35h extended Write Fpdma Queued 61hWrite Multiple Command C5h, 39h extended Write Sectors 30h, 34h extendedSpinpoint M9T Product Manual REV General Information MaintenanceMaintenance Precautions HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks