Samsung M9T manual Smart B0h, Smart Feature Registers Values, Smart disable operations D9h

Page 68

8.2.34 SMART (B0h)

Individual SMART commands are identified by the value placed in the Feature resister. Below depicts these Feature register values.

Table 8-14 SMART Feature Registers Values

Feature Value

Command

D0h

SMART READ DATA

D1h

Obsolete (SMART Read Threshold)

D2h

SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE

D3h

Obsolete (SMART Save Attribute Value)

D4h

SMART EXECUTE OFF-LINE IMMEDIATE

D5h

SMART READ LOG SECTOR

D6h

SMART WRITE LOG SECTOR

D7h

Obsolete

D8h

SMART ENABLE OPERATIONS

D9h

SMART DISABLE OPERATIONS

DAh

SMART RETURN STATUS

DBh

Obsolete (Enable/Disable Auto Offline Scan)

DCh-DDh

Reserved

DEh

Reserved

DFh

Reserved

8.2.34.1Smart disable operations (D9h)

This command disables all SMART capabilities within the device including any timer and event count functions related to this feature. After receipt of this command the device shall disable all SMART operations. SMART data shall no longer be monitored or saved by the device. The state of SMART (either enabled or disabled) shall be preserved by the device across power cycles.

After receipt of this command by the device, all other SMART commands (including SMART DISABLE OPERATIONS commands), with the exception of SMART ENABLE OPERATIONS, are disabled and invalid and shall be command aborted by the device.

8.2.34.2Smart enable/disable attribute auto-save (D2h)

This command enables and disables the optional attribute auto-save feature of the device. Depending upon the implementation, this command may either allow the device, after some vendor specified event, to automatically save its updated attribute values to non-volatile memory; or this command may cause the auto- save feature to be disabled. The state of the attribute auto-save feature (either enabled or disabled), shall be preserved by the device across power cycles.

A value of zero written by the host into the device’s Sector Count register before issuing this command shall cause this feature to be disabled. Disabling this feature does not preclude the device from saving SMART data to non-volatile memory during some other normal operation such as during a power-on sequence or during an error recovery sequence.

Spinpoint M9T Product Manual REV 1.0

63

Page 67 Page 69
Image 68
Page 67 Page 69
Contents M9T Product Manual Page Table of Contents Iii Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Manual Organization ScopeUser Definition Sata ReferenceDescription IntroductionKey Features Standards and Regulations Hardware RequirementsSpecifications Specification SummaryPhysical Specifications Logical ConfigurationsPerformance Specifications Power consumption Power consumptionPower Requirements RatedEnvironmental Specifications Environmental SpecificationsLinear Shock 1/2 sine pulse Rotational ShockReliability Specifications Installation Space RequirementsUnpacking Instructions MountingMounting Dimensions OrientationSata Connectivity Cable ConnectorsVentilation Computer mainboard or Serial ATA host adapter Power ManagementSATA-Bus Interface Connector HDD Power, Sata Interface, and Factory Jumper ConnectorDrive Installation DC Power Connector and SATA-Bus Interface Cable ConnectionsHead / Disk Assembly HDA Base Casting AssemblyDC Spindle Motor Assembly Disk Drive OperationExploded Mechanical View Disk Stack Assembly Head Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration SystemDisk Controller Digital Signal Process and Interface ControllerDrive Electronics DDR Host Interface Control Block Buffer Control BlockFrequency Synthesizer Disk Control BlockDisk Ldpc Control Block Power Management Read/Write ICTime Base Generator Automatic Gain ControlAnalog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIRRead Channel Servo SystemRead and Write Operations Read Caching Firmware FeaturesWrite Channel Write Caching Defect Management Automatic Defect AllocationSmart 6 APMSata II Interface Sata TerminologySpinpoint M9T Product Manual REV Physical Interface Signal Summary Signal DescriptionsWhen read When written 2 I/O Register AddressControl Block Register Descriptions RegistersCommand Block Register Descriptions Command Register Ex F7h Device Register Ex F6hStatus Register Ex F7h Sata II Feature SET Device Activity SignalStaggered Spin-up Disable Control Auto-Activate in DMA Setup FISPhy Event Counters Software Settings Preservation Sata Power ManagementCommand Code Parameters ATA Command DescriptionsCommand Table Smart Command Descriptions Check Power Mode E5hDevice Configuration Overlay B1h Download Micro Code 92hDevice Configuration Identify data structure Word Content Execute Device Diagnostics 90h Diagnostic CodesFlush Cache E7h, EAh extended Format Track 50hContent Description Identify Device information=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWNIdle Immediate E1h Automatic Standby Timer PeriodsIdle E3h Initialize Device Parameters 91h NOP 00hRead Buffer E4h Read DMA C8h, 25h extendedRead Long 22h Read Multiple Command C4h, 29h extendedRead Log Extended 2Fh Read Verify Sectors 40h, 41h extended Read Native Max Address F8h, 27h extendedRead Sectors 20h, 24h extended Security Disable Password F6h Recalibrate 10hSecurity Erase Prepare F3h Security Erase Unit F4hSecurity Set Password F1h Security Erase Unit Password Word ContentSecurity Set Password data content Security Freeze Lock F5hSeek 7xh Set Features EFhSecurity Unlock F2h 11 Set Features Register Definitions 12 Transfer Mode ValuesSet Multiple Mode C6h 13 Set Max Feature Register ValuesSet Max Address F9h, 37h extended Sleep E6h14 Smart Feature Registers Values Smart disable operations D9hSmart enable/disable attribute auto-save D2h Smart B0hSmart enable operations D8h Smart execute off-line immediate D4hSmart read data D0h 15 Device Smart Data StructureByte Bit Name Description 16 Smart Attribute Status Flags17 Smart Attribute Data List 18 Off-line Data Collection Status ValuesSelf-test execution status byte 19 Self-test Execution Status ValuesSmart write log sector D6h Smart read log sector D5hSmart return status DAh Standby Immediate E0h Write Buffer E8hWrite DMA CAh, 35h extended Write Fpdma Queued 61hWrite Multiple Command C5h, 39h extended Write Sectors 30h, 34h extendedSpinpoint M9T Product Manual REV General Information MaintenanceMaintenance Precautions HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks
Top Page Image Contents