RCA 1616262A manual Using Automatic Code Search

Page 13

Using the Remote Control

Using Automatic Code Search

The following instructions can be used to program the remote to operate each of your components. If you want to stop the automatic code search without programming any of your components, press CLEAR until the indicator light on the remote turns off.

1.Turn on the component you want to operate (VCR or DVD player)

2.Press and hold the component button you want to program (VCR or DVD). While holding the component button, press and hold ON¥OFF until the indicator light on the remote turns on, then release both buttons.

3.Point the remote at the component. Press and release PLAY (the indicator light on the remote flashes).

The remote is searching for the correct code to program. When the indicator stops flashing (after about 5 seconds), press PLAY again to tell the remote to search the next set of codes.

Continue pressing PLAY until the component turns off or the indicator light on the remote turns off. If the indicator light turns off, then all the codes for that particular component have been tested once. If the component does not turn off, then the remote canÕt be programmed to operate that component.

Note: Each time you press PLAY, the remote sends about 10 sets of codes. Therefore, you might have to press the PLAY button up to 20 times.

If the component you want to operate does turn off:

1.Press and release REVERSE, then wait 2 seconds. Repeat this step until the device turns back ON.

2.To finish, press and hold STOP until the indicator on the remote turns off.

Using Direct Entry

1.Turn on the component to be programmed.

2.Look up the brand and code number(s) for the component on the code list in this section.

3.Press and hold the component button you want to program on the remote.

4.Enter the code from the remote control code list on the following pages. If the indicator flashes, you have either entered an invalid code or the button isnÕt programmable.

5.Release the component button.

6.Point the remote at the component. Press ON¥OFF to see if the component responds to the command. If it doesnÕt, try pressing the component button and then ON¥OFF again.

¥If you get no response, repeat these steps using the next code listed for your brand, until the component responds to the remote commands.

¥If you try all the codes for your component brand and none work, try the automatic code search method. If automatic code search doesnÕt find the code, the remote is not compatible with your component.

Chapter 2

Graphics contained within this publication are for representation only.

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Television Users Guide Product Registration Important InformationProduct Information Table of Contents Table of Contents Chapter Things to Consider Before You ConnectConnect your DVD Player to your TV Connections & SetupConnect your TV to your VCR Make sure cable or antenna is connected to your VCRPr Pb Y Explanation of JacksFront Input Jacks Front of Your TVFront Panel Buttons Complete the Initial Setup How to Use the Remote Control to Complete the Initial SetupPlug in the TV Put batteries in the remoteComplete Auto Channel Search VOL or VOL + Decreases or increases the TVÕs volume Button Descriptions for TV ModeButton Descriptions for DVD and VCR Modes Using the Input Button Using the Remote ControlProgramming the Remote to Operate Other Components Find Out If You Need to Program the RemoteUsing Automatic Code Search How to Use the Remote After You’ve Programmed It Remote Control CodesVCR Codes Programmable for VCR buttonProgrammable for DVD button VCR CodesHow to Set Up the Auto Tuning Feature Why You Should Use the Auto Tuning FeatureChannel Banner Parental Controls and V-Chip Using the TV’s FeaturesUSA V-Chip Rating System How V-Chip WorksCanadian English V-Chip Rating System Canadian French V-Chip Rating System To set TV programming limits USA V-Chip TV Rating LimitViewing Specific Content Themes Blocking Specific Content ThemesChip Movie Rating Limit Blocking Canadian V-Chip RatingsChip Exempt Program Block Change PasswordChip Active Front Panel LockPicture Menu Sound MenuSetup Menu Using the TV’s Menu SystemTime Menu Parental Control MenuTroubleshooting Other Information Limited Warranty Care and CleaningProduct Registration Limitation of Warranty What your warranty does not coverHow state law relates to this warranty If you purchased your product outside the United StatesRemote Control This is Thomson Inc North Meridian Street Indianapolis, Tocom 1616262A Transforme encore le divertissement Flip over for EnglishEnregistrement du produit Information importanteInformation sur le produit DŽtaillant / Adresse / TŽlŽphoneContrle parental et V-chip Codes de tŽlŽcommandeDŽpannage Entretien et nettoyage Garantie limitŽe Table des matiresPrŽvenez les surtensions ChapitreProtŽgez vos composants contre la surchauffe Utilisez un Žclairage indirectTŽlŽviseur + lecteur DVD + magnŽtoscope Connexions et rŽglageConnectez votre lecteur DVD à votre téléviseur Connectez votre téléviseur à votre magnétoscopeMono Audio Explication des prisesAvant du tŽlŽviseur Power Alimentation Allume et Žteint le tŽlŽviseurPrises dÕentrŽe avant Boutons du panneau avantExŽcution de lÕinstallation initiale Insertion des piles dans la tŽlŽcommandeBranchement du tŽlŽviseur Mise en marche du tŽlŽviseurRecherche automatique complte de canaux Description des touches pour les modes DVD et VCR Description des touches pour le mode TVComment savoir si vous devez programmer la tŽlŽcommande Utilisation de la tŽlŽcommandeProgrammation de la tŽlŽcommande Utilisation de la touche InputRel‰chez la touche du composant Si le composant que vous voulez commander s’éteintUtilisation de la tŽlŽcommande une fois programmŽe Codes de tŽlŽcommandeCodes pour magnŽtoscopes Programmable pour la touche VCRProgrammable pour la touche DVD Codes pour magnŽtoscopes suitePourquoi utiliser la fonction de syntonisation automatique Bannire de canalRŽglage de la fonction de syntonisation automatique Contrle parental et V-chip Utilisation des fonctions du tŽlŽviseurDes choix et de brves explications suivent Systme de filtrage TV pour les ƒ-U Fonctionnement du V-chipSystme de filtrage TV pour le Canada anglais Systme de filtrage TV pour le Canada franais Pour fixer la limite Filtrage TV pour les ƒ-UVisionnement de thmes particuliers Blocage de thmes particuliersFiltrage des films V-chip Blocage pour le filtrage canadienDŽterminez les thmes que vous voulez changer ˆ V Voir SŽlectionnez V-chip USA SŽlectionnez Filtrage filmsChip actif Blocage des Žmissions sans codeVerrouillage du panneau avant Changement de mot de passeMenu Image Menu SonUtilisation du systme de menus du tŽlŽviseur Menu InstallationMenu Horloge Menu Contrle parentalDŽpannage Autres informations Garantie limitŽe Entretien et nettoyageEnregistrement du produit Limitation de la garantie Ce que ne couvre pas votre garantieLÕeffet des lois provinciales sur cette garantie ANT200 DT6DC 1,82 m Télécommande CÕestDT12DC 3,65 m Thomson
Top Page Image Contents