Mitsubishi Electronics PD-5030, PD-6130 manual How to Attach Options to the Plasma Monitor

Page 10

How to Attach Options to the Plasma Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

*While it is upright. (See Drawing A)

*As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

*Do not touch or hold the screen face when carrying the unit.

•This device cannot be installed on its own. Be sure to use a stand or other mounting hardware that is designed specifically for this product.

•For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only a matching stand or wall mount kit designed for this product.

Drawing A

Drawing B

When installing or carrying, use the handles attached to the upper back of the display.

Ventilation requirements for enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing.

	Wall
50mm (2")	50mm (2")	(2")
		(2")

50mm			Wall
			Wall

How to use the safety metal fittings and the screws for safety metal fittings

These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws. * Safety metal fittings will differ according to the model.

Screw hole

Screw or Hook etc. (Not supplied)

50mm (2") (2")mm 50

Safety metal fittings

Screw for Safty metal fittings

Metal chain (Not supplied)

Wall

Table Top

1

Image 10

Contents Owner’s Guide Page Important Safety Instructions PD-5030/PD-6130 Important Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Page Plasma Display Screen & Cabinet Cleaning SafeguardsImportant No Abrasives Introduction Features you’ll enjoy includeContents of the Package Introduction to the PD-5030/ PD-6130 Plasma MonitorsContents How to Attach Options to the Plasma Monitor Ventilation requirements for enclosure mountingPart Names and Function Front ViewRear View/ Terminal Board EXT Speaker L and RRemote Control RGB/PCBattery Installation and Replacement 5AUTO PositionOperating Range Using the wired remote control modeHandling the remote control Approx 7m/23ftMitsubishi HD Receiver/Controller InstallationHD-5000 Connecting Your VCR or Laser Disc Player Connecting Your DVD PlayerMonitorLink and MonitorLink Control MonitorLink Pin Configuration DVI ConnectorMonitorLink Connections External DVI Device with DVI-HDCPCable Management Video signal RGB/DVD/HD signalLoop Out ClampTo check the settings To adjust the sound volumeTo cancel the sound To adjust the size or quality of the picture automaticallyAfter the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Format SizesNarrow screen size 43 or Sxga Format Operation with Computer Signals Supported resolution Expand screen sizeOn-Screen Menu OSM Controls Menu OperationsVideo Settings Menu Adjusting the pictureAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture Gamma settings Making the Low Tone adjustments Adjusting the white balance LOW Tone settings Audio settings menu Audio Settings Menu Colorview settings ColorViewAdjusting the Position, Size, Fine Picture, Picture Adj Monitor Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuExample Set the BNC Input mode to Comp Setting the BNC connectorsSetting a computer image to the correct RGB select screen BNC Input Settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images Peak Bright settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screenOrbiter settings Orbiter Function settingsSetting the time Inverse SettingsSetting the time for INVERSE/WHITE ExampleGray Level settings Setting the screen size for S1/S2 video inputSoft Focus settings Soft FocusPLUG/PLAY settings Setting the signal and black level for DVI signalS1/S2 settings Black Level settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the program Setting the power on mode Program Timer settings Special characters in the Program Timer screen Button Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings IR Remote settingsTo set the Loop OUT to on Loop Out setting Loop OUT settings To connect another displaySetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections RS-232C ControlApplication Communication ParametersTroubleshooting Symptom Checks RemedyPage Specifications PD-5030 SignalsSpecifications PD-6130 Supported resolution Table of Signals SupportedComputer input signals supported by this system Page Mitsubishi Plasma Display Panel Limited Warranty Declaration of Conformity