Mitsubishi Electronics PD-5030 manual Reducing noise in the picture, Setting the color temperature

Page 26

Reducing noise in the picture

Use these settings if the picture has noise due to poor reception or when playing video tapes with poor picture quality.

Example: Setting “NR-3”

1.On the MAIN MENU, select “VIDEO SETTINGS”, then press the MENU/ENTER button.

The “VIDEO SETTINGS” screen appears.

2.Use the and buttons to select “NR”.

 

 

VIDEO SETTINGS

1 / 2

CONTRAST

 

 

 

 

 

 

 

BRIGHTNESS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SHARPNESS

 

 

 

 

 

 

 

COLOR

 

 

 

 

 

 

 

TINT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PICTURE MODE

 

:

NORMAL

 

 

 

NR

NEXT PAGE

 

:

OFF

 

 

 

 

 

 

 

 

 

 

 

 

SEL.

ADJ.

 

EXIT

RETURN

3.Use the  and  buttons to select “NR-3”.

The mode switches as follows each time the  or  button is pressed:

OFF NR-1 NR-2 NR-3

 

 

NR

: NR-3

 

 

*If neither the  or  button is pressed within 5 seconds, the current selection is stored into memory and the previous screen reappears.

Information

NR

*“NR” stands for Noise Reduction.

*This function reduces noise in the picture.

Types of noise reduction

There are three settings for noise reduction. Each has a different level of noise reduction.

The effect becomes stronger as the number increases (in the order NR-1NR-2NR-3).

OFF

Turns the noise reduction function off.

Setting the color temperature

Use this procedure to set color tone produced by the plasma display.

Example: Setting “HIGH”

1.On the MAIN MENU, select “VIDEO SETTINGS”, then press the MENU/ENTER button.

The “VIDEO SETTINGS” screen appears.

2.Use the and buttons to select “NEXT PAGE”.

3.Select “COLOR TEMP”.

4.Use the  and  buttons to select “HIGH”.

The mode switches as follows each time the  or  button is pressed:

LOW MID LOW MEDIUM HIGH

* See below to set “WHITE BALANCE”.

 

 

 

VIDEO SETTINGS

2 / 2

 

 

PREVIOUS PAGE

 

 

 

 

 

COLOR TEMP.

 

:

HIGH

 

 

 

 

 

 

 

 

 

GAMMA

 

 

:

2

 

 

LOW TONE

 

 

:

AUTO

 

COLORVIEW

 

 

 

 

 

 

 

 

SEL.

 

ADJ.

 

 

RETURN

 

 

 

 

EXIT

*If neither the  or  button is pressed within 5 seconds, the current selection is stored into memory and the previous screen reappears.

Information

Setting the color temperature

LOW

Redder

MID LOW

Slightly redder

MEDIUM

Standard (slightly bluer)

HIGH

Bluer

Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

Adjusting the color to the desired level

Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality.

Example: Adjusting the “GAIN RED” of “HIGH” color temperature

Perform Steps 1-4 of SETTING THE COLOR

TEMPERATURE, then...

5.Press the MENU/ENTER button.

The “WHITE BALANCE” screen appears.

6.Use the and buttons to select “GAIN RED”.

WHITE BALANCE

COLOR TEMP. HIGH

GAIN RED

 

 

GAIN GREEN

 

 

GAIN BLUE

 

 

BIAS RED

 

 

BIAS GREEN

 

 

BIAS BLUE

 

 

RESET

 

: OFF

SEL.

ADJ.

EXIT RETURN

17

Image 26
Contents Owner’s Guide Page Important Safety Instructions PD-5030/PD-6130 Risk of Electric Shock Do not Open PrecautionsImportant Information To avoid damage and prolong operating life Page Important No Abrasives Cleaning SafeguardsPlasma Display Screen & Cabinet Introduction Features you’ll enjoy includeContents of the Package Introduction to the PD-5030/ PD-6130 Plasma MonitorsContents How to Attach Options to the Plasma Monitor Ventilation requirements for enclosure mountingPart Names and Function Front ViewRear View/ Terminal Board EXT Speaker L and RRemote Control RGB/PCBattery Installation and Replacement 5AUTO PositionOperating Range Using the wired remote control modeHandling the remote control Approx 7m/23ftHD-5000 InstallationMitsubishi HD Receiver/Controller Connecting Your VCR or Laser Disc Player Connecting Your DVD PlayerMonitorLink and MonitorLink Control MonitorLink Pin Configuration DVI ConnectorMonitorLink Connections External DVI Device with DVI-HDCPCable Management Video signal RGB/DVD/HD signalLoop Out ClampTo check the settings To adjust the sound volumeTo cancel the sound To adjust the size or quality of the picture automaticallyAfter the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWhen viewing videos or digital video discs Format SizesNarrow screen size 43 or Sxga Format Operation with Computer Signals Supported resolution Expand screen sizeOn-Screen Menu OSM Controls Menu OperationsVideo Settings Menu Adjusting the pictureReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level  Gamma settings Making the Low Tone adjustments Adjusting the white balance  LOW Tone settings Audio settings menu Audio Settings Menu Colorview settings ColorViewAdjusting the Position, Size, Fine Picture, Picture Adj Monitor Settings MenuSetting the allocation of the audio connectors Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuExample Set the BNC Input mode to Comp Setting the BNC connectorsSetting a computer image to the correct RGB select screen  BNC Input Settings Input Skip settings Setting high definition images to the suitable screen sizeSetting the Input Skip  RGB Select modesSetting the power management for computer images Option2 Settings MenuResetting to the default values Peak Bright settings POWER/STANDBY indicatorSetting the picture to suit the movie Reducing burn-in of the screenOrbiter settings Orbiter Function settingsSetting the time Inverse SettingsSetting the time for INVERSE/WHITE ExampleGray Level settings Setting the screen size for S1/S2 video inputSoft Focus settings Soft FocusPLUG/PLAY settings Setting the signal and black level for DVI signalS1/S2 settings Black Level settings Present Time settings Option3 Settings MenuUsing the timer Present Time To reset the program Setting the power on mode Program Timer settings  Special characters in the Program Timer screen Button Lock settings Enabling/disabling remote control wireless transmission PWR. on Mode settings  IR Remote settingsTo set the Loop OUT to on Loop Out setting Loop OUT settings  To connect another displaySetting the language for the menus Language Settings MenuColor System Settings Menu Setting the video signal formatConnections RS-232C ControlApplication Communication ParametersTroubleshooting Symptom Checks RemedyPage Specifications PD-5030 SignalsSpecifications PD-6130 Computer input signals supported by this system Table of Signals SupportedSupported resolution Page Mitsubishi Plasma Display Panel Limited Warranty Declaration of Conformity