Mitsubishi Electronics PD-6130, PD-5030 manual Using the wired remote control mode, Operating Range

Page 15

Using the wired remote control mode

Connect one end of the remote cable to the remote control’s REMOTE JACK and the other end to the “REMOTE IN” terminal on the monitor. When the cable is connected, the mode automatically switches to wired remote control. When the wired remote control mode is used, the remote control can be operated even if no batteries are installed.

Operating Range

*Use the remote control within a distance of about 7 m/ 23ft. from the front of the monitor’s remote control sensor and at horizontal and vertical angles of up to approximately 30°.

*The remote control operation may not function if the monitor’s remote control sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between the sensor and the remote control.

(		AUDIO2 R
MONO
)	L
	Cr/Pr	R/
	G/ Y		RGB
	Cb/Pb	B/	2 / DVD2
	HD		/ HD2
	VD
	(IN / OUT		RGB 1
	)
(		AUDIO 3 R
MONO
)	L
	DV I ( Digital RGB		MONITORLINK
	)
	Monitorlink Control
	IN
	REMOTE
	OUT

MONITORLINK CONTROL

IN

REMOTE

OUT

Remote Control

Cable

Approx.

7m/23ft

To Remote Jack

Handling the remote control

•Do not drop or mishandle the remote control.

•Do not get the remote control wet. If the remote control gets wet, wipe it dry immediately.

•Avoid heat and humidity.

•When using the remote control in the wireless condition, be sure to unplug the remote cable from the REMOTE IN terminal on the monitor.

•Do not mix new and old batteries.

•Do not heat, take apart, or throw batteries into a fire.

•When the remote control is not being used for a long period of time, remove the batteries.

6

Image 15

Contents Owner’s Guide Page Important Safety Instructions PD-5030/PD-6130 Precautions Important InformationRisk of Electric Shock Do not Open To avoid damage and prolong operating life Page Cleaning Safeguards Plasma Display Screen & CabinetImportant No Abrasives Introduction to the PD-5030/ PD-6130 Plasma Monitors Features you’ll enjoy includeContents of the Package IntroductionContents Ventilation requirements for enclosure mounting How to Attach Options to the Plasma MonitorFront View Part Names and FunctionEXT Speaker L and R Rear View/ Terminal BoardRGB/PC Remote Control5AUTO Position Battery Installation and ReplacementApprox 7m/23ft Using the wired remote control modeHandling the remote control Operating RangeInstallation Mitsubishi HD Receiver/ControllerHD-5000 Connecting Your DVD Player Connecting Your VCR or Laser Disc PlayerExternal DVI Device with DVI-HDCP MonitorLink Pin Configuration DVI ConnectorMonitorLink Connections MonitorLink and MonitorLink ControlClamp Video signal RGB/DVD/HD signalLoop Out Cable ManagementTo adjust the size or quality of the picture automatically To adjust the sound volumeTo cancel the sound To check the settingsTo check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerFormat Sizes When viewing videos or digital video discsExpand screen size Format Operation with Computer Signals Supported resolution Narrow screen size 43 or SxgaMenu Operations On-Screen Menu OSM ControlsAdjusting the picture Video Settings MenuSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settingsColorView Audio Settings Menu Colorview settings Audio settings menuExample Setting Audio INPUT1 to Video Monitor Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu BNC Input Settings Setting the BNC connectorsSetting a computer image to the correct RGB select screen Example Set the BNC Input mode to Comp RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settingsOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie Peak Bright settingsOrbiter Function settings Orbiter settingsExample Inverse SettingsSetting the time for INVERSE/WHITE Setting the timeSoft Focus Setting the screen size for S1/S2 video inputSoft Focus settings Gray Level settingsBlack Level settings Setting the signal and black level for DVI signalS1/S2 settings PLUG/PLAY settingsPresent Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode Program Timer settings To reset the program IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Button Lock settings To connect another display Loop Out setting Loop OUT settings To set the Loop OUT to onSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters RS-232C ControlApplication ConnectionsSymptom Checks Remedy TroubleshootingPage Signals Specifications PD-5030Specifications PD-6130 Table of Signals Supported Supported resolutionComputer input signals supported by this system Page Mitsubishi Plasma Display Panel Limited Warranty Declaration of Conformity