Runco XP-OPAL65, XP-OPAL50 Or 1080p and the Aspect Ratio is set to 169 refer to, Sound

Page 51

Operation

Note	1. 1:1 PIXEL MODE is available only when the input signal is 1080i
	or 1080p and the Aspect Ratio is set to 16:9 (refer to page 23).

2.You cannot adjust H-SIZE,V-SIZEor DOT CLOCK when 1:1 PIXEL MODE is enabled.

Use the controls in the SOUND menu to adjust the CinemaWall audio settings.

SOUND

To return all SOUND menu settings to their factory-default values, press RESET on the remote control unit with the menu on-screen. Or, press or repeatedly to highlight RESET in the menu, then press the ACTION () button.

SOUND

RESET

NORMAL

AUDIO MENU

DYNAMIC

BASS

0

MID

0

TREBLE

0

BALANCE

0

SURROUND

ON

AUDIO OUT (PIP)

MAIN

RETURN

RESET

ADJUST

SELECT

AUDIO MENU: The CinemaWall provides three audio memories for storing and recalling sound quality settings. To store settings in an audio memory, highlight AUDIO MENU in the SOUND menu and select STANDARD, DYNAMIC or CLEAR. The CinemaWall “remembers” any adjustments you make when you switch to a different audio memory, then switch back.

BASS/MID/TREBLE: Use these controls to boost or cut the low, mid-range and high frequencies respectively in the audio signal.

BALANCE: To adjust the left/right speaker balance, select BALANCE from the SOUND menu. Use the or buttons to make one channel louder than the other.

SURROUND: The CinemaWall has a “surround sound” mode that simulates a multi-channel sound system. To use the surround mode, select SURROUND from the SOUND menu and set it to ON.

AUDIO OUT (PIP): To swap the main and PIP audio programs when using the

MULTI PIP feature, select AUDIO OUT (PIP) from the SOUND menu and set it to either

MAIN or SUB. For more on MULTI PIP mode, refer to MULTI PIP SETUP on page 43.

CinemaWall Installation/Operation Manual

37

Image 51

Contents XP-65 XP-50Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. Default SettingsList of Figures List of Figures Xiv Target Audience Carriage return must be used after each command or stringIntroduction About This ManualDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50 and XP-OPAL50 Controls and Indicators Controls and FunctionsCinemaWall at a Glance Display Stand XP-50 / XP-OPAL50 XP-65 / XP-OPAL65 ConnectorsPower Input Surround button CinemaWall Remote ControlControls and Functions Installation Remote ControlOther surfaces Step Procedure For Details, refer to Quick SetupInstallation must be performed by a qualified custom video Installation specialistInstallation Considerations Ventilation Ambient LightOther Considerations Components to Connecting SourceConnections to CinemaWallDVD Analog RGB Connections Connection Connecting External Speakers OptionalConnector Pin Assignments RS-232 ControllerAC Power Connection Turning on the Power Changing the OSD Language Setting the Day and TimeOperation Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio149 169Edges of the screen 43 431 linearly scalesSource image horizon Played at the left and rightActivating PIP Swapping the Main PIP Images Using Picture-In-Picture PIPChanging the PIP Window Position Using the On-Screen MenusSelecting a PIP Target Screen or Input SourcePOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separatelyFrequency is 108 MHz or greater Options menu refer to page 50 is set to OnSound Or 1080p and the Aspect Ratio is set to 169 refer toSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language onOn hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to onPresent Time Setup Refer to Setting the Day and Time on Command Timer refer toDVD3 Operation Refer to Return ChangeCurrently active Level see belowPicture menu is set to Warm When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when MULTI-DISPLAY is activeUsing Digital Zoom During the delay period, the power indicator flashes greenOn page 21, the Clock Display setting has no effect Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlSymptom Possible Causes Solution Troubleshooting TipsExamples Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes Serial CommunicationsHex Description Serial CommandsDamzoom IMSPC1 SSCFNC0 VDO VWBGCT-30 Serial Communications CinemaWall Specifications SpecificationsCinemaWall Dimensions 12.31 Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default SettingsDefault Settings Page 020-0970-01 Rev. a September