Runco XP-OPAL65 Using Digital Zoom, During the delay period, the power indicator flashes green

Page 65

Operation

Power On Screen Delay: In a large video wall installation, it may be advisable to turn the displays on one at a time rather than all at once, so as not to overload the power source.

To make this easier, you can set the CinemaWall to wait up to 30 seconds after you press the POWER button to turn itself on. To do this, select Power On Screen Delay from the OPTIONS menu. Select from 1 to 30 seconds of delay. For example, in a 2x2 video wall you might set a 4-second delay on display “A1,” an 8-second delay on display “A2,” a 12-second delay on display “A3” and no delay (Off) on display “A4.”

During the delay period, the power indicator flashes green.

Note

Clock Display: To have the CinemaWall display the time of day (in addition to the current input and aspect ratio) when the RECALL button is pressed, select Clock Display from the OPTIONS menu and set it to On.

Note	Until you set the day and time (refer to Setting the Day and Time
	on page 21), the Clock Display setting has no effect.

All Aspect: This option controls which aspect ratio selections are available to the viewer. Set it to On to allow the viewer to select all of the aspect ratios described in Table 4-1.If the viewer does not need that level of aspect ratio control, set it to Off for the sake of simplicity.

Rotate: If the CinemaWall is suspended from a ceiling, you may want to mount it upside down and run the cables upward (toward the ceiling) to make them less visible. If you do, select Rotate from the OPTIONS menu and set it to On to rotate the displayed image and OSD menus 180 degrees.

Serial Slot Select: This menu option does not currently apply to the CinemaWall.

The CinemaWall allows you to zoom in on a portion of the displayed image. To use this feature:

4.9

Using Digital Zoom

1.Press the MOVE/ZOOM () button.

2.An on-screen guide appears. Press the

ACTION () button to select a zoom level (x1, x2, x3 or x4).

3.Press , , or to select an area of the image to enlarge. The on-screen guide shows you the selected area as you do this.

EXIT

1

4. To return to normal viewing mode, press RETURN (RETURN ) or MOVE/ZOOM ().

CinemaWall Installation/Operation Manual

51

Image 65

Contents XP-65 XP-50Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Specifications Maintenance and TroubleshootingAppendix A. Default Settings OperationList of Figures List of Figures Xiv Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50 and XP-OPAL50 CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand XP-50 / XP-OPAL50 XP-65 / XP-OPAL65 ConnectorsPower Input Surround button CinemaWall Remote ControlControls and Functions Other surfaces InstallationRemote Control Installation must be performed by a qualified custom video Quick SetupInstallation specialist Step Procedure For Details, refer toInstallation Considerations Ventilation Ambient LightOther Considerations Connections to Connecting SourceCinemaWall Components toDVD Analog RGB Connections Connector Pin Assignments Connecting External Speakers OptionalRS-232 Controller ConnectionAC Power Connection Operation Turning on the Power Changing the OSD LanguageSetting the Day and Time Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio149 169Source image horizon 43 431 linearly scalesPlayed at the left and right Edges of the screenActivating PIP Swapping the Main PIP Images Using Picture-In-Picture PIPSelecting a PIP Target Using the On-Screen MenusScreen or Input Source Changing the PIP Window PositionPOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separatelyFrequency is 108 MHz or greater Options menu refer to page 50 is set to OnSound Or 1080p and the Aspect Ratio is set to 169 refer toSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language onOn hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to onPresent Time Setup Refer to Setting the Day and Time on Command Timer refer toDVD3 Operation Refer to Return ChangeCurrently active Level see belowSome cases, power is transmitted to the slot when When using multiple displays such as in a video wall RuncoMULTI-DISPLAY is active Picture menu is set to WarmOn page 21, the Clock Display setting has no effect Using Digital ZoomDuring the delay period, the power indicator flashes green Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenSymptom Possible Causes Solution Troubleshooting TipsCommand 3 bytes Parameter 6 bytes Command 3 bytes Parameter 3 bytesSerial Communications ExamplesHex Description Serial CommandsDamzoom IMSPC1 SSCFNC0 VDO VWBGCT-30 Serial Communications CinemaWall Specifications SpecificationsCinemaWall Dimensions 12.31 Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default SettingsDefault Settings Page 020-0970-01 Rev. a September