Runco XP-OPAL65, XP-OPAL50 operation manual Operation

Page 61

Operation

Weekly Command Timer: You can program the CinemaWall to perform a series of actions at specific times of the day and days of the week. To do this, you create command sequences or “programs” consisting of a series of up to 64 individual commands. You can create up to seven such programs and specify when they are executed.

For example, you can store the following command sequence as a program:

1.8:00 - Power On

2.8:01 - Select INPUT1A

3.8:01 - Set Volume to 30

4.8:15 - Enable Multi-PIP

5.8:20 - Activate Screen Saver

6.8:30 - Deactivate Screen Saver

7.9:00 - Power Off

To configure the Weekly Command Timer, select it in the OPTIONS menu and press the

ACTION () button.

•Function: This is the “master switch” for the Weekly Command Timer feature. Set it to On to use this method to automate CinemaWall operation.

If you enable the Weekly Command Timer, you cannot use the SET

Note UP TIMER, nor can you use the INTERVAL or TIME OF DAY screen saver modes.

•Monday, Tuesday ... Sunday: For each day of the week, select a program (Program1 ... Program7) that you want to use that day to control the CinemaWall. Or, select “---” for manual operation.

CinemaWall Installation/Operation Manual

47

Image 61

Contents XP-65 XP-50Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Specifications Maintenance and TroubleshootingAppendix A. Default Settings OperationList of Figures List of Figures Xiv Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50 and XP-OPAL50 Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand XP-50 / XP-OPAL50 XP-65 / XP-OPAL65 ConnectorsPower Input Surround button CinemaWall Remote ControlControls and Functions Remote Control InstallationOther surfaces Installation must be performed by a qualified custom video Quick SetupInstallation specialist Step Procedure For Details, refer toInstallation Considerations Ventilation Ambient LightOther Considerations Connections to Connecting SourceCinemaWall Components toDVD Analog RGB Connections Connector Pin Assignments Connecting External Speakers OptionalRS-232 Controller ConnectionAC Power Connection Setting the Day and Time Turning on the Power Changing the OSD LanguageOperation Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio149 169Source image horizon 43 431 linearly scalesPlayed at the left and right Edges of the screenActivating PIP Swapping the Main PIP Images Using Picture-In-Picture PIPSelecting a PIP Target Using the On-Screen MenusScreen or Input Source Changing the PIP Window PositionPOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separatelyFrequency is 108 MHz or greater Options menu refer to page 50 is set to OnSound Or 1080p and the Aspect Ratio is set to 169 refer toSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language onOn hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to onPresent Time Setup Refer to Setting the Day and Time on Command Timer refer toDVD3 Operation Refer to Return ChangeCurrently active Level see belowSome cases, power is transmitted to the slot when When using multiple displays such as in a video wall RuncoMULTI-DISPLAY is active Picture menu is set to WarmDuring the delay period, the power indicator flashes green Using Digital ZoomOn page 21, the Clock Display setting has no effect Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenSymptom Possible Causes Solution Troubleshooting TipsCommand 3 bytes Parameter 6 bytes Command 3 bytes Parameter 3 bytesSerial Communications ExamplesHex Description Serial CommandsDamzoom IMSPC1 SSCFNC0 VDO VWBGCT-30 Serial Communications CinemaWall Specifications SpecificationsCinemaWall Dimensions 12.31 Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default SettingsDefault Settings Page 020-0970-01 Rev. a September