Runco XP-OPAL50, XP-OPAL65 When using multiple displays such as in a video wall Runco

Page 64

Operation

Initial Power Mode: Select Initial Power Mode from the OPTIONS menu to control how the CinemaWall recovers from a power interruption (resulting either from a power failure or from being unplugged, then plugged back in):

•Normal: The CinemaWall returns to whatever power-on state it was in before the power interruption.

•Standby: The CinemaWall comes on in standby mode. The power indicator lights red or orange.

•On: The CinemaWall returns to “power on” mode. The power indicator lights green.

When using multiple displays – such as in a video wall – Runco

Note recommends setting this to “Standby” in order to minimize power load.

ID select/Remote ID/Serial ID: These menu options do not currently apply to the

CinemaWall.

Display size: Select Display size from the OPTIONS menu and set it to On to reduce the size of the displayed image by approximately five percent (5%).

Note	1. This setting is not available when MULTI-PIP, Digital Zoom or
	MULTI-DISPLAY is active.

2.When Display size is set to On, the H-SIZE/V-SIZEcontrols (in the POS./SIZE menu) are not available and only the 16:9 and 4:3 aspect ratios can be selected.

Studio W/B: Select Studio W/B from the OPTIONS menu and set it to On to set the color temperature to a level appropriate for television broadcast applications.

Note	Setting Studio W/B to On has no effect unless the COLOR TEMP
	(in the PICTURE menu) is set to WARM.

Studio Gain: Select Studio Gain from the OPTIONS menu and set it to On to sharpen the contrast for a better view when a part of the image is too light to see.

Slot power: Select Slot power from the OPTIONS menu to control when power is transmitted to the terminal boards installed in SLOT1, SLOT2 and SLOT3. Choose one of the following:

•Off: Power is not transmitted to the slot power.

•Auto: Power is transmitted to the slot power only when main power is on.

•On: Power is transmitted to the slot power when main power is on or in the standby state.

In some cases, power is transmitted to the slot when the

Note CinemaWall is on or in the standby state regardless of the Slot power setting.

50	CinemaWall Installation/Operation Manual

Image 64

Contents XP-50 XP-65Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting SpecificationsAppendix A. Default Settings OperationList of Figures List of Figures Xiv Carriage return must be used after each command or string IntroductionAbout This Manual Target AudienceUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-50 and XP-OPAL50 Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand Connectors XP-50 / XP-OPAL50 XP-65 / XP-OPAL65Power Input CinemaWall Remote Control Surround buttonControls and Functions Remote Control InstallationOther surfaces Quick Setup Installation must be performed by a qualified custom videoInstallation specialist Step Procedure For Details, refer toInstallation Considerations Ambient Light VentilationOther Considerations Connecting Source Connections toCinemaWall Components toDVD Analog RGB Connections Connecting External Speakers Optional Connector Pin AssignmentsRS-232 Controller ConnectionAC Power Connection Setting the Day and Time Turning on the Power Changing the OSD LanguageOperation Setting the Computer Display Properties Selecting an Input Source Changing the Aspect Ratio Aspect ratio selection is saved independently for each input169 14943 431 linearly scales Source image horizonPlayed at the left and right Edges of the screenUsing Picture-In-Picture PIP Activating PIP Swapping the Main PIP ImagesUsing the On-Screen Menus Selecting a PIP TargetScreen or Input Source Changing the PIP Window PositionPOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness CinemaWall memorizes position and size settings separately POS./SIZEOptions menu refer to page 50 is set to On Frequency is 108 MHz or greaterOr 1080p and the Aspect Ratio is set to 169 refer to SoundSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Refer to Changing the OSD Language on Order to activate multi-display mode, you must first setOn hides joints between displays C D Transparency cannot be used when Insert is set to on Insert cannot be used when Transparency is set to onCommand Timer refer to Present Time Setup Refer to Setting the Day and Time onDVD3 Operation Return Change Refer toLevel see below Currently activeWhen using multiple displays such as in a video wall Runco Some cases, power is transmitted to the slot whenMULTI-DISPLAY is active Picture menu is set to WarmDuring the delay period, the power indicator flashes green Using Digital ZoomOn page 21, the Clock Display setting has no effect Operation Maintenance and Troubleshooting CleaningCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionCommand 3 bytes Parameter 3 bytes Command 3 bytes Parameter 6 bytesSerial Communications ExamplesSerial Commands Hex DescriptionDamzoom IMSPC1 SSCFNC0 VDO VWBGCT-30 Serial Communications Specifications CinemaWall SpecificationsCinemaWall Dimensions 12.31 Supported Timings Supported Signal Timings by Input Specifications Appendix A. Default Settings Table A-1. Runco Factory Default Settings for CinemaWallDefault Settings Page 020-0970-01 Rev. a September