Runco XP-65DHD manual Typical Gray Bar Pattern for Adjusting Contrast

Page 52

Operation

PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes.

Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that:

•The darkest black bars disappear into the background.

•The dark gray areas are barely visible.

•The lighter gray areas are clearly visible.

•The white areas are a comfortable level of true white.

•The image contains only black, gray and white (no color).

Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-3.

Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast

Select Contrast and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size.

Brightness and contrast controls are interactive. A change to one

Note may require a subtle change to the other in order to achieve the optimum setting.

40	PlasmaWall XP Series Owner’s Operating Manual

Image 52

Contents XP-103DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-65DHD and XP-65DHDxa Optional Accessories XP-50DHD and XP-50DHDxaOptional Accessories XP-103DHD Controls and Functions Controls and IndicatorsPlasmaWall at a Glance Display Stand Connectors PlasmaWall Rear PanelDHD Controller Front Panel Slot 1 Not used Slot 2 DVI-D or Dual Hdmi inputController to this input Slot 3 Not used PC in Not used RS-232C 9-pin, male D-SubEnter Button DHD Controller Rear Panel Outputs 1. Hdmi OUTComLink RS-232 Output RS-232 Control PortDHD Controller Remote Control DHD Controller Remote ControlOn / OFF Cursor KeysVideo Comp ComponentMemory Preset Buttons Aspect Ratio Selection Buttons16 9 Letbox LetterboxInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation Considerations Ambient Light VentilationVentilation Requirements for Enclosure Mounting XP-103DHD Other Considerations Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerPlasmaWall Rear Panel Connecting the PlasmaWall DVI Version to the DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source Components to the DHDHdmi Connections See Figure ControllerDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toConnecting an External IR Receiver to the DHDConnecting AC Power 14. AC Power Connection15. Cable Management Turning on the Power Setting the Computer Display Properties OperationOperation Using the DHD Controller Menus Input Source Aspect RatioMemory Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio 169 Letterbox VirtualWide CinemaAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanMemory Presets InformationCalibration Operation Input Names Restore Composite Video Component SD ServiceShould be used by ISF-certified technicians only Exit PlasmaWall stores any changes you make to these settings HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Maintenance and Troubleshooting CleaningCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionPlasmaWall Maintenance and Troubleshooting Serial Communications Letterbox EnterValue Description Min/max Stored? Power On/Off Commands CommandInput Selection Commands Memory Preset Commands Iheight Miscellaneous Commands available on all inputs Hdinputres YESCommand Parameter min/max Value Stored? Description Enter keySpecifications PlasmaWall SpecificationsDHD Controller Specifications Dimensions PlasmaWall10.0 PlasmaWall Model XP-103DHD Dimensions with Floor Stand Specifications Page Runco CL-810 Owner’s Operating Manual