Runco XP-65DHD manual PlasmaWall stores any changes you make to these settings

Page 60

Operation

Display Device: The options in the Display Device menu allow you to perform certain adjustments at the plasma display.

•Display Position: Select Display Position from the Display Device menu to perform the following display device adjustments (these are global, independent of any input):

•Select Left/Right or Up/Down and use the or buttons to fine-tune the displayed image position.

•Select Width or Height and use the or buttons to fine-tune the display device aspect ratio.

•Select Pix By Pix from the Display Position menu and set it to Enable to have the PlasmaWall map a 1920x1080 input signal to 1080p HD panel pixels, displaying 100% of the original content. By skipping the scaling process, the PlasmaWall can produce high-definition images in their original, 1:1 pixel form.

When Pix By Pix mode is disabled, the picture source is scaled for over-scanning and 97% of the original is displayed. Use this setting to minimize or elimate image flicker.

1. Pix By Pix is available only when the input signal is 1080i or

Note 1080p.

2.You cannot adjust the Width or Height when Pix By Pix is enabled.

•Display Image (1080i digital and 1080p signals ONLY): Select Display Image from the Display Device menu to perform the following display device adjustments.

•Brightness

•Contrast

•Sharpness

•Color Temperature

•AGC

•Input Level

•Gain (red and blue)

•Offset (red and blue)

•Gamma

For detailed instructions for making these adjustments, refer to Calibration on page 44.

The PlasmaWall stores any changes you make to these settings in

Note the currently-selected ISF preset (ISF Day or ISF Night). After calibrating the display for one ISF preset, save your settings, select the other ISF preset and repeat the process.

48	PlasmaWall XP Series Owner’s Operating Manual

Image 60

Contents XP-103DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-50DHD and XP-50DHDxa Optional Accessories XP-65DHD and XP-65DHDxaOptional Accessories XP-103DHD Controls and Indicators Controls and FunctionsPlasmaWall at a Glance Display Stand Connectors PlasmaWall Rear PanelDHD Controller Front Panel Slot 1 Not used Slot 2 DVI-D or Dual Hdmi inputController to this input Slot 3 Not used PC in Not used RS-232C 9-pin, male D-SubEnter Button DHD Controller Rear Panel Outputs 1. Hdmi OUTComLink RS-232 Output RS-232 Control PortDHD Controller Remote Control DHD Controller Remote ControlOn / OFF Cursor KeysVideo Comp ComponentMemory Preset Buttons Aspect Ratio Selection Buttons16 9 Letbox LetterboxInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation Considerations Ambient Light VentilationVentilation Requirements for Enclosure Mounting XP-103DHD Other Considerations Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerPlasmaWall Rear Panel Connecting the PlasmaWall DVI Version to the DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source Components to the DHDHdmi Connections See Figure ControllerDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toConnecting an External IR Receiver to the DHDConnecting AC Power 14. AC Power Connection15. Cable Management Turning on the Power Setting the Computer Display Properties OperationOperation Using the DHD Controller Menus Input Source Aspect RatioMemory Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio 169 Letterbox VirtualWide CinemaAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanMemory Presets InformationCalibration Operation Service Input Names Restore Composite Video Component SDShould be used by ISF-certified technicians only Exit PlasmaWall stores any changes you make to these settings HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Maintenance and Troubleshooting CleaningCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionPlasmaWall Maintenance and Troubleshooting Serial Communications Letterbox EnterCommand Value Description Min/max Stored? Power On/Off CommandsInput Selection Commands Memory Preset Commands Iheight Miscellaneous Commands available on all inputs Hdinputres YESCommand Parameter min/max Value Stored? Description Enter keySpecifications PlasmaWall SpecificationsDHD Controller Specifications Dimensions PlasmaWall10.0 PlasmaWall Model XP-103DHD Dimensions with Floor Stand Specifications Page Runco CL-810 Owner’s Operating Manual