Runco XP-65DHD manual Input Position Left/Right Up/Down Width Height Overscan

Page 54

Operation

Input Position ➤

Input Position

Left/Right

Up/Down

Width

Height

Overscan

Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5.Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.

Figure 4-5. Typical Test Pattern for Adjusting Sharpness

Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position for the current source.

Note	The input position settings are automatically saved for each input
	and resolution.

Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Use the right or up cursor button to shift the image to the right; use the left or down button to shift it to the left.

Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Use the right or up cursor button to shift the image upward; use the left or down button to shift it downward.

Width: Select Width from the Input Position menu to change the projected image width. Use the right or up cursor button to increase the width; use the left or down button to decrease it.

Height: Select Height from the Input Position menu to change the projected image height. Use the right or up cursor button to increase the height; use the left or down button to decrease it.

42	PlasmaWall XP Series Owner’s Operating Manual

Image 54

Contents XP-103DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-50DHD and XP-50DHDxa Optional Accessories XP-65DHD and XP-65DHDxaOptional Accessories XP-103DHD Controls and Indicators Controls and FunctionsPlasmaWall at a Glance Display Stand Connectors PlasmaWall Rear PanelController to this input DHD Controller Front PanelSlot 1 Not used Slot 2 DVI-D or Dual Hdmi input Slot 3 Not used PC in Not used RS-232C 9-pin, male D-SubEnter Button DHD Controller Rear Panel Outputs 1. Hdmi OUTComLink RS-232 Output RS-232 Control PortDHD Controller Remote Control DHD Controller Remote ControlVideo On / OFFCursor Keys Comp Component16 9 Memory Preset ButtonsAspect Ratio Selection Buttons Letbox LetterboxInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation Considerations Ambient Light VentilationVentilation Requirements for Enclosure Mounting XP-103DHD Other Considerations Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerPlasmaWall Rear Panel Connecting the PlasmaWall DVI Version to the DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Hdmi Connections See Figure Connecting SourceComponents to the DHD ControllerDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection Connecting 12-VoltRS-232 Controller Trigger Outputs toConnecting an External IR Receiver to the DHDConnecting AC Power 14. AC Power Connection15. Cable Management Turning on the Power Setting the Computer Display Properties OperationOperation Using the DHD Controller Menus Input Source Aspect RatioInput Source Memory PresetsService Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio 169 Letterbox VirtualWide CinemaAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanMemory Presets InformationCalibration Operation Service Input Names Restore Composite Video Component SDShould be used by ISF-certified technicians only Exit PlasmaWall stores any changes you make to these settings HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionPlasmaWall Maintenance and Troubleshooting Serial Communications Letterbox EnterCommand Value Description Min/max Stored? Power On/Off CommandsInput Selection Commands Memory Preset Commands Iheight Miscellaneous Commands available on all inputs Hdinputres YESCommand Parameter min/max Value Stored? Description Enter keySpecifications PlasmaWall SpecificationsDHD Controller Specifications Dimensions PlasmaWall10.0 PlasmaWall Model XP-103DHD Dimensions with Floor Stand Specifications Page Runco CL-810 Owner’s Operating Manual