Runco XP-50DHD, XP-50DHDxa, XP-65DHD, XP-65DHDxa, XP-103DHD manual Operation

Page 57

Operation

ISF Night - Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance at the DHD Controller (as opposed to the display device). These settings are also saved independently for each input.

Gain/Offset: These controls operate similarly to those in the ISF Night - Display Color menu (see above), but affect the Y, Pb and Pr signal components rather than the red and blue channels.

Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or “noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

ISF Day - Display Color: Refer to ISF Night - Display Color.

ISF Day - Input Image: Refer to ISF Night - Input Image.

ISF Day - Input Color: Refer to ISF Night - Input Color.

Save ISF Settings: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Settings from the ISF Calibration menu to do this. In the event you ever have to perform a System Reset, you can restore the saved ISF settings by selecting Restore Saved Settings in the Service menu. (System Reset and Restore Saved Settings are described on page 50.)

Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal. These settings are saved independently for each aspect ratio.

Splash Configure: Use the Splash Configure menu to customize the appearance of the start-up message that appears on the vacuum fluorescent display upon power-up.

Owner Name/ISF Calibrated/ISF Other: You can have the PlasmaWall display the owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up to 20 characters in length.

Use the up or down cursor button to select a character. Use the right and left cursor buttons to change the cursor position. Press MENU when you have finished entering text. Then, check the “Splash Enable” box to have the PlasmaWall display the information you enter here when it is turned on.

PlasmaWall XP Series Owner’s Operating Manual

45

Image 57
Contents XP-103DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsList of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50DHD and XP-50DHDxa Optional Accessories XP-65DHD and XP-65DHDxaOptional Accessories XP-103DHD Controls and Indicators Controls and FunctionsPlasmaWall at a Glance Display Stand PlasmaWall Rear Panel ConnectorsSlot 1 Not used Slot 2 DVI-D or Dual Hdmi input DHD Controller Front PanelController to this input Slot 3 Not used PC in Not used RS-232C 9-pin, male D-SubEnter Button Outputs 1. Hdmi OUT DHD Controller Rear PanelRS-232 Control Port ComLink RS-232 OutputDHD Controller Remote Control DHD Controller Remote ControlCursor Keys On / OFFVideo Comp ComponentAspect Ratio Selection Buttons Memory Preset Buttons16 9 Letbox LetterboxRemote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupInstallation Considerations Ventilation Ambient LightVentilation Requirements for Enclosure Mounting XP-103DHD Other Considerations Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerPlasmaWall Rear Panel Connecting the PlasmaWall DVI Version to the DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceHdmi Connections See Figure ControllerDigital DTV RGB Connections Digital DTV RGB Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureRS-232 Controller Connecting 12-VoltConnection Trigger Outputs toReceiver to the DHD Connecting an External IR14. AC Power Connection Connecting AC Power15. Cable Management Operation Turning on the Power Setting the Computer Display PropertiesOperation Input Source Aspect Ratio Using the DHD Controller MenusService Memory PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio 169 Letterbox VirtualWide CinemaRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionInformation Memory PresetsCalibration Operation Service Input Names Restore Composite Video Component SDShould be used by ISF-certified technicians only Exit PlasmaWall stores any changes you make to these settings HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenSymptom Possible Causes Solution Troubleshooting TipsPlasmaWall Maintenance and Troubleshooting Letterbox Enter Serial CommunicationsCommand Value Description Min/max Stored? Power On/Off CommandsInput Selection Commands Memory Preset Commands Iheight Hdinputres YES Miscellaneous Commands available on all inputsEnter key Command Parameter min/max Value Stored? DescriptionPlasmaWall Specifications SpecificationsDHD Controller Specifications PlasmaWall Dimensions10.0 PlasmaWall Model XP-103DHD Dimensions with Floor Stand Specifications Page Runco CL-810 Owner’s Operating Manual