Sanyo PLC-XP57L owner manual Indicators and Projector Condition, SXGA2

Page 55

APPENDIX

When a input signal is digital from DVI terminal, refer to the chart below.

✳

ON-SCREEN	RESOLUTION	H-Freq.	V-Freq.
DISPLAY		(kHz)	(Hz)

D-VGA		640 x 480	31.47	59.94
D-480p		720 x 480	31.47	59.88
D-480p		(Progressive)	31.47	59.88
D-575p		768 x 575	31.25	50.00
D-575p		(Progressive)	31.25	50.00
D-SVGA		800 x 600	37.879	60.32
D-XGA		1024 x 768	43.363	60.00
D-WXGA1		1366 x 768	48.36	60.00
D-WXGA2		1360 x 768	47.70	60.00
D-WXGA3		1376 x 768	48.36	60.00
D-WXGA5		1368 x 768	46.50	50.00
D-SXGA1		1280 x 1024	63.98	60.02

ON-SCREEN	RESOLUTION	H-Freq.	V-Freq.
DISPLAY		(kHz)	(Hz)

✳ D-SXGA2	1280 x 1024	60.276	58.069
✳ D-SXGA+ 1	1400 x 1050	63.97	60.19
D-720p	1280 x 720	45.00	60.00
	(Progressive)
D-720p	1280 x 720	37.50	50.00
	(Progressive)
D-1035i	1920 x 1035	33.75	60.00
	(Interlace)
D-1080i	1920 x 1080	33.75	60.00
	(Interlace)
D-1080i	1920 x 1080	28.125	50.00
	(Interlace)
D-1080psf/30	1920 x 1080	33.75	60.00
D-1080psf/25	1920 x 1080	28.125	50.00
D-1080psf/24	1920 x 1080	27.00	48.00

✳Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.

NOTE: Specifications are subject to change without notice.

INDICATORS AND PROJECTOR CONDITION

Check the indicators for projector condition.

	Indicators
				Projector Condition
LAMP	WARNING	READY	LAMP	Projector Condition
REPLACE	TEMP.	green	red
yellow	red	green	red
yellow	red

				The projector is OFF. (The AC power cord is unplugged.)

✽				The projector is ready to be turned on with the POWER ON-
✽				OFF button.
				OFF button.

✽				The projector is operating normally.

				The Warning Temp. indicator blinks red to let you know the
				internal temperature of the projector exceeds a normal level. If
				the temperature goes up further, the projector will be turned
✽				off automatically and the Ready indicator goes out. When the
✽				projector is cooled down enough and the temperature returns
				projector is cooled down enough and the temperature returns
				to normal, the READY indicator lights green and the projector
				can be turned on again. (The WARNING TEMP. indicator
				keeps blinking.) Check and clean the air filters.

				The projector is cooled down enough and the temperature
✽				returns to normal. When turning on the projector, the
✽				WARNING TEMP. indicator stops blinking. Check and clean
				WARNING TEMP. indicator stops blinking. Check and clean
				the air filters.

• • • on	• • • blinking		• • • dim	• • • off

55

Image 55

Contents Model PLC-XP57L Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsCompliance AC Power Cord RequirementTable of Contents Compact Design Digital Zoom for Computer Features and DesignName of Each Part of Projector PreparationConnecting AC Power Cord SETTING-UP ProjectorFor the U.S.A. and Canada Preparation Lens Installation Installing Projector in Proper Position Preparation Adjustable FeetNo Sideways Preparation Moving Projector Terminals of Projector Connecting ProjectorTerminals Projector Connecting to ComputersTerminals Connecting to Video EquipmentBefore Operation Remote Control OperationLaser Pointer Function Before Operation Remote Control Batteries InstallationInput Button TOP Controls and IndicatorsLamp Replace Indicator Ready Indicator Lamp Indicator Point Volume + / ButtonsON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on the Projector What is PIN code?Basic Operation Turning on / OFF ProjectorBasic Operation Turning OFF the Projector Keystone Correction Adjusting ScreenFocus Adjustment Lens Shift AdjustmentNo Show Function Sound AdjustmentTimer Function Basic Operation Picture Freeze FunctionInput Menu Computer InputSelecting Input Source RGB AV HdcpSelecting Computer System Manually When Selecting Input 2 5 BNC Input JacksSelecting Computer System Automatic MULTI-SCAN SystemAuto PC adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Quit ResetMode free StoreImage Level Select Picture Image SelectImage Select Menu Picture Screen Select Picture Screen AdjustmentScreen Menu Video Input When Selecting Input 3 AV TerminalsVideo Video Jack or S-VIDEO Jack Component Video Signal FormatSelecting Video System Video InputImage button Standard Cinema CinemaProvides image at the normal video aspect ratio Picture Image Picture Image AdjustmentsImage Adjust Menu Pointer ModeDEL Color MMenu Color PaletteSharpness White balance RedWhite balance Green White balance BlueSetting Menu SettingSetting Menu Language Logo PIN code lock LogoLogo select CaptureAnamorphic Power managementCeiling RearLamp control Remote controlTo change the code of the remote control On startSecurity Key lock Wireless Mouse modeProjector mode USBTo Change the PIN Code PIN code lock To Change the PIN Code Lock settingChanging the PIN code lock setting PIN code lockQuit Lamp counter Factory defaultAppendix Wireless MouseInstallation Operating Wireless MouseAppendix MaintenanceCleaning Projection Lens Appendix AIR Filters Care and CleaningPOA-LMP101 Lamp ReplacementOrder Replacement Lamp PLC-XP57LLamp counter Appendix Lamp Replace CounterProblem Try these Solutions TroubleshootingNot work ServiceImage Select Screen PC AdjustMenu Tree SystemSound SettingImage Adjust Image SelectResolution Appendix Compatible Computer SpecificationsSXGA2 Indicators and Projector ConditionProjector is in cooling mode. It cannot be turned on until Input 1 Jacks Technical SpecificationsTerminal Mini DIN 8-PIN Pin Configuration Appendix Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Terminal DVI 24-pin Pin ConfigurationPJ Link Notice Lens ReplacementTo the sales and service engineers Appendix Optional PartsLogo PIN Code Lock No Appendix PIN Code Number MemoDimensions 1AA6P1P5225-- KE6A