Sanyo PLC-XP57L owner manual Appendix Lamp Replace Counter, Lamp counter

Page 49

APPENDIX

LAMP REPLACE COUNTER

Be sure to reset the Lamp replacement counter after the lamp assembly is replaced. When the Lamp replacement counter is reset, the LAMP REPLACE indicator stops lighting.

1

Turn the projector on and press the MENU button to display

Lamp counter

 

 

the On-Screen Menu. Press the POINT LEFT/RIGHT buttons

 

 

to move the red frame pointer to the SETTING Menu icon

 

2

Press the POINT UP/DOWN buttons to move the red frame

 

 

pointer to Lamp counter and then press the SELECT button.

 

 

The next box appears.

 

3

Press the POINT UP/DOWN buttons to select Reset and then

 

 

press the SELECT button. The “Lamp replacement counter

 

 

reset?” appears. Move the pointer to [Yes] and then press the

 

 

SELECT button.

 

4

Another confirmation dialog box appears and select [Yes] to

 

 

reset the Lamp replacement counter.

 

NOTE:

Do not reset the Lamp replacement counter until after the projection lamp is replaced.

Select Lamp counter and this box appears. Select [Reset], and the next box appears.

Select [Yes], and then another confirmation box appears.

Select [Yes] again to reset the lamp counter.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the LAMP REPLACEMENT section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

49

Image 49
Contents Model PLC-XP57L Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsCompliance AC Power Cord RequirementTable of Contents Compact Design Digital Zoom for Computer Features and DesignName of Each Part of Projector PreparationConnecting AC Power Cord SETTING-UP ProjectorFor the U.S.A. and Canada Preparation Lens Installation Installing Projector in Proper Position Preparation Adjustable FeetNo Sideways Preparation Moving Projector Terminals of Projector Connecting ProjectorTerminals Projector Connecting to ComputersTerminals Connecting to Video EquipmentBefore Operation Remote Control OperationLaser Pointer Function Before Operation Remote Control Batteries InstallationLamp Replace Indicator Ready Indicator Lamp Indicator TOP Controls and IndicatorsPoint Volume + / Buttons Input ButtonON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Basic Operation What is PIN code?Turning on / OFF Projector Turning on the ProjectorBasic Operation Turning OFF the Projector Focus Adjustment Adjusting ScreenLens Shift Adjustment Keystone CorrectionTimer Function Sound AdjustmentBasic Operation Picture Freeze Function No Show FunctionSelecting Input Source Computer InputRGB AV Hdcp Input MenuSelecting Computer System When Selecting Input 2 5 BNC Input JacksAutomatic MULTI-SCAN System Selecting Computer System ManuallyAuto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC adjComputer Input Manual PC Adjustment Mode free ResetStore QuitImage Level Select Picture Image SelectImage Select Menu Picture Screen Select Picture Screen AdjustmentScreen Menu Video Input When Selecting Input 3 AV TerminalsVideo Selecting Video System Component Video Signal FormatVideo Input Video Jack or S-VIDEO JackImage button Standard Cinema CinemaProvides image at the normal video aspect ratio Image Adjust Menu Picture Image AdjustmentsPointer Mode Picture ImageMenu Color MColor Palette DELWhite balance Green White balance RedWhite balance Blue SharpnessSetting Menu SettingSetting Menu Language Logo select LogoCapture Logo PIN code lockCeiling Power managementRear AnamorphicTo change the code of the remote control Remote controlOn start Lamp controlProjector mode Wireless Mouse modeUSB Security Key lockChanging the PIN code lock setting To Change the PIN Code Lock settingPIN code lock To Change the PIN Code PIN code lockQuit Lamp counter Factory defaultInstallation Wireless MouseOperating Wireless Mouse AppendixAppendix MaintenanceCleaning Projection Lens Appendix AIR Filters Care and CleaningOrder Replacement Lamp Lamp ReplacementPLC-XP57L POA-LMP101Lamp counter Appendix Lamp Replace CounterProblem Try these Solutions TroubleshootingNot work ServiceMenu Tree PC AdjustSystem Image Select ScreenImage Adjust SettingImage Select SoundResolution Appendix Compatible Computer SpecificationsSXGA2 Indicators and Projector ConditionProjector is in cooling mode. It cannot be turned on until Input 1 Jacks Technical SpecificationsTerminal HDB15-PIN Pin Configuration Appendix Configurations of TerminalsTerminal DVI 24-pin Pin Configuration Terminal Mini DIN 8-PIN Pin ConfigurationTo the sales and service engineers Lens ReplacementAppendix Optional Parts PJ Link NoticeLogo PIN Code Lock No Appendix PIN Code Number MemoDimensions 1AA6P1P5225-- KE6A