Runco VX-8D operation manual Installing the Fixed CineWide Base Plate VX-8d/CineWide

Page 43

Installation

Figure 3-9shows the anamorphic lens base plate assembly for a VX-8d/CineWide.

Installing the Fixed CineWide Base Plate (VX-8d/CineWide)

1 Screw, Phillips Pan-Head, 10-32 x 3/8” (8x)

2Anamorphic Lens Base Plate

Ceiling Mount

Rails (part of

Ceiling Mount

Kit)

Figure 3-9. VX-8d/CineWide with Anamorphic Lens Base Plate and Ceiling Mounting Rails - Exploded View

To install the fixed CineWide base plate on a VX-8d/CineWide:

1.Place the projector upside down on a blanket or other soft surface.

2.Place the CineWide base plate on the bottom of the projector.

3.If you are mounting the projector on a ceiling: Line up the three holes on the left and right mounting rails (included with the projector ceiling mount kit) with those on the bottom of the projector and CineWide base plate.

Runco VX-8d Installation/Operation Manual

27

Image 43
Contents VX-8d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures Xvi About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories VX-8d at a Glance Controls and FunctionsExhaust Vent VX-8d Rear Panel Power Input 100 to 240 VAC Connect the VX-8d to power hereRS-232C Input 9-pin, female D-Sub Virtual Cinema is available only on the VX-8d/CineWide or DHD Controller Front PanelPanel DHD Controller RearDisplay Control Inputs 4. USB DHD Controller/VX-8d Remote Control VX-8d Remote Control UnitMenu button see below to exit the current menu On / OFFCursor Buttons Information about aspect ratios, refer to TableLetbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 169Controls and Functions Remote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Throw Distance Ambient LightLens VX-8d Lens Options and Throw RatiosThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input Timings Audio/VideoOther Considerations Installing the Optional CineWide Lens MountLens Motor VX-8d/CineWide with AutoScope Installing the AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Ceiling Mounting Adjusting the ProjectionDo not use the mounting screws provided with the ceiling Floor Mounting UprightController to the VX-8d Connector Panel AccessConnecting the DHD Connections to the VX-8d and DHD Controller11. RS-232 Connection from the DHD Controller to the VX-8d Controller Connecting SourceComponents to the DHD Hdmi Source Connections See FigureDTV-Set-Top Box 13. Component Video Source Connections14. Rgbhv Source Connections Computer RGB Camcorder15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerInput voltage to the AutoScope lens motor must be between Focus Zoom Vertical and Horizontal Lens Shift Primary Lens AdjustmentsAdjusting the Picture Orientation You must enter a passcode to access the Service menuAnamorphic Lens Installation Adjustment Installing and Adjusting the CineWide Anamorphic LensIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusMain Menu ServiceRunco Video Aspect Ratio Input SourceAspect Ratio Input SourceHdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets System SignalInformation InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF Settings CalibrationColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation Color X/y Color Gamut ValuesOperation 58 and ISF Day/Night Memory Presets Operation Lamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerEnter VX-8d Specifications SpecificationsVX-8d Specifications Limited Warranty Home Theater Calibration SpecificationsIndustry-Standard Specifications Weight without lensDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions with Optional Ceiling Mount VX-8d DimensionsVX-8d/CineWide Dimensions with Optional Ceiling Mount VX-8d/CineWide DimensionsVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May
Related manuals
Manual 104 pages 38.93 Kb