Runco VX-8D Home Theater Calibration Specifications, Industry-Standard Specifications

Page 98

Specifications

Table 7-1. VX-8d Specifications (continued)

Brightness and Contrast:	Cinema Standards Measurement System (CSMS)
	Specifications
	-	Brightness: 110 foot-Lamberts (fL)
	-	Contrast Ratio: 251:1
	These measurements are taken from the projector in a controlled,
	home theater environment. All measurements are made to
	ANSI/NAPM IT7.228-1997 specifications using the Photo Research
	PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
	Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
	projector is calibrated to a color temperature of 6,500K and has a
	minimum of 150 hours of usage.
	The foot-Lambert (fL) is the unit of measurement used in commercial
	movie theaters to express image brightness at the screen surface. The
	Society of Motion Picture and Television Engineers (SMPTE) specifies
	16 fL as the target image brightness for film-based projectors using an
	open gate (without film in the projector). More importantly, today
	SMPTE specifies 12 fL as the target image brightness in Digital
	Cinema theaters. The foot-Lambert measurement is dependent on
	screen size, screen gain and projector light output.
	Home Theater Calibration Specifications
	-	Light Output: 1708 ANSI Lumens
	-	Contrast Ratio: 251:1
	These specifications are obtained by calibrating the projector as
	described above for CSMS measurements.
	Industry-Standard Specifications
	-	Light Output: 2000 ANSI Lumens
	-	Contrast Ratio: 10,000:1
	These are typical projector brightness and contrast specifications
	found in most companies’ sales literature. Runco includes these
	measurements in its literature to allow for direct comparison with other
	manufacturers’ projectors. These measurements are typically taken at
	9,000K to 13,000K to get expected performance data when the
	projector is used in professional, commercial and industrial displays.

Weight (without lens):	69.0 lbs. (31.30 kg)

Regulatory Approvals:	Complies with FCC, CE

Limited Warranty:	Projector: Two (2) years parts and labor from the date of
	delivery to the end user.
	Lamp: 1000 hours or six (6) months, whichever comes first.

Specifications are subject to change without notice.

82	Runco VX-8d Installation/Operation Manual

Image 98

Contents VX-8d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures Xvi Introduction About This ManualSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-8d at a GlanceExhaust Vent RS-232C Input 9-pin, female D-Sub Power Input 100 to 240 VAC Connect the VX-8d to power hereVX-8d Rear Panel DHD Controller Front Panel Virtual Cinema is available only on the VX-8d/CineWide orDisplay Control DHD Controller RearPanel Inputs 4. USB VX-8d Remote Control Unit DHD Controller/VX-8d Remote ControlInformation about aspect ratios, refer to Table On / OFFCursor Buttons Menu button see below to exit the current menu169 Memory Preset ButtonsAspect Ratio Selection Buttons Letbox LetterboxControls and Functions Installation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Ambient Light Throw DistanceLens Option VX-8d Lens Options and Throw RatiosThrow Range Throw Ratio Inches, with LensVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Audio/Video Synchronization IssuesPossible Audio Latency for Various Input Timings Input Timing Possible Audio Latency millisecondsInstalling the Optional CineWide Lens Mount Other ConsiderationsInstalling the AutoScope Lens Motor VX-8d/CineWide with AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Floor Mounting Upright Adjusting the ProjectionDo not use the mounting screws provided with the ceiling Ceiling MountingConnections to the VX-8d and DHD Controller Connector Panel AccessConnecting the DHD Controller to the VX-8d11. RS-232 Connection from the DHD Controller to the VX-8d Hdmi Source Connections See Figure Connecting SourceComponents to the DHD Controller13. Component Video Source Connections DTV-Set-Top BoxComputer RGB Camcorder 14. Rgbhv Source ConnectionsGaming Console 15. Scart Rgbs Source ConnectionsComposite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens MotorConnecting an External IR Receiver to the DHDInput voltage to the AutoScope lens motor must be between Turning on the PowerConnecting to AC Power You must enter a passcode to access the Service menu Primary Lens AdjustmentsAdjusting the Picture Orientation Focus Zoom Vertical and Horizontal Lens ShiftIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Time after turning on the systemInstallation Anamorphic Lens Top View Geometry Using the On-Screen Menus OperationRunco Video ServiceMain Menu Input Source Input SourceAspect Ratio Aspect RatioSelect 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Information SignalInformation SystemCalibration You must enter a passcode to access the Calibration menuCalibration ISF Settings Should be used by ISF-certified technicians onlyColor Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesOperation Copied settings are not retained after a power cycle Copy/PasteInput Names ServiceService Exit Operation X/y Color Gamut Values ColorOperation 58 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyWith Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter VX-8d Specifications SpecificationsVX-8d Specifications Weight without lens Home Theater Calibration SpecificationsIndustry-Standard Specifications Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions VX-8d Dimensions with Optional Ceiling MountVX-8d/CineWide Dimensions VX-8d/CineWide Dimensions with Optional Ceiling MountVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May

Related manuals

Manual 104 pages 38.93 Kb