Runco VX-8D AutoScope Lens Motor, Connecting 12-volt Trigger Outputs to External Equipment

Page 53

Installation

If your VX-8d is equipped with a CineWide with AutoScope system, connect the AutoScope lens motor to a 12-volt trigger output on the DHD Controller; see Figure 3-18.

Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or screen masks) to the other trigger outputs.

AutoScope Lens Motor

Power

AC Input

Switch

 

3.5-mm mini plug

Connecting 12-volt

Trigger Outputs to

External Equipment

Retractable Screen or other

12-volt trigger-activatedSleeve = Ground

device

Tip = +12V

Figure 3-18. Connecting 12-volt Trigger Outputs

Runco VX-8d Installation/Operation Manual

37

Image 53
Contents VX-8d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures Xvi About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories VX-8d at a Glance Controls and FunctionsExhaust Vent RS-232C Input 9-pin, female D-Sub Power Input 100 to 240 VAC Connect the VX-8d to power hereVX-8d Rear Panel Virtual Cinema is available only on the VX-8d/CineWide or DHD Controller Front PanelDisplay Control DHD Controller RearPanel Inputs 4. USB DHD Controller/VX-8d Remote Control VX-8d Remote Control UnitCursor Buttons On / OFFInformation about aspect ratios, refer to Table Menu button see below to exit the current menuAspect Ratio Selection Buttons Memory Preset Buttons169 Letbox LetterboxControls and Functions Installation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Throw Distance Ambient LightThrow Range Throw Ratio Inches, with VX-8d Lens Options and Throw RatiosLens Option LensFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Possible Audio Latency for Various Input Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Installing the Optional CineWide Lens MountLens Motor VX-8d/CineWide with AutoScope Installing the AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Do not use the mounting screws provided with the ceiling Adjusting the ProjectionFloor Mounting Upright Ceiling MountingConnecting the DHD Connector Panel AccessConnections to the VX-8d and DHD Controller Controller to the VX-8d11. RS-232 Connection from the DHD Controller to the VX-8d Components to the DHD Connecting SourceHdmi Source Connections See Figure ControllerDTV-Set-Top Box 13. Component Video Source Connections14. Rgbhv Source Connections Computer RGB Camcorder15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRInput voltage to the AutoScope lens motor must be between Turning on the PowerConnecting to AC Power Adjusting the Picture Orientation Primary Lens AdjustmentsYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens ShiftIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusRunco Video ServiceMain Menu Aspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Information SignalInformation SystemCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleInput Names ServiceService Exit Operation Color X/y Color Gamut ValuesOperation 58 and ISF Day/Night Memory Presets Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyWith Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter VX-8d Specifications SpecificationsVX-8d Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions with Optional Ceiling Mount VX-8d DimensionsVX-8d/CineWide Dimensions with Optional Ceiling Mount VX-8d/CineWide DimensionsVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May
Related manuals
Manual 104 pages 38.93 Kb