Runco VX-8D operation manual Installation

Page 60

Installation

Adjusting the Height (Y): With the white field still on-screen, loosen the Height/Y Adjustment T-Screws on either side of the lens. Then, slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

When the height is properly set, tighten the Height Adjustment T-Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below the Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Correct Lens Angle

Incorrect Lens Angle

The anamorphic lens will almost always be angled with respect to the projector; this is normal.

Once the proper lens angle has been set, firmly tighten the Pitch Adjustment T-Screws to secure the lens in place.

There may be some pincushion distortion even after the lens is

Note properly adjusted, especially at shorter throw distances. If this is the case, Runco recommends that you slightly over-scan the image into the screen frame area to mask the distortion.

44

Runco VX-8d Installation/Operation Manual

Image 60
Contents VX-8d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsExternal Control Table of Contents Xiv List of Figures Xvi Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-8d at a GlanceExhaust Vent Power Input 100 to 240 VAC Connect the VX-8d to power here VX-8d Rear PanelRS-232C Input 9-pin, female D-Sub DHD Controller Front Panel Virtual Cinema is available only on the VX-8d/CineWide orDHD Controller Rear PanelDisplay Control Inputs 4. USB VX-8d Remote Control Unit DHD Controller/VX-8d Remote ControlOn / OFF Cursor ButtonsInformation about aspect ratios, refer to Table Menu button see below to exit the current menuMemory Preset Buttons Aspect Ratio Selection Buttons169 Letbox LetterboxControls and Functions Installation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Ambient Light Throw DistanceVX-8d Lens Options and Throw Ratios Throw Range Throw Ratio Inches, withLens Option LensCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Synchronization Issues Possible Audio Latency for Various Input TimingsAudio/Video Input Timing Possible Audio Latency millisecondsInstalling the Optional CineWide Lens Mount Other ConsiderationsInstalling the AutoScope Lens Motor VX-8d/CineWide with AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Adjusting the Projection Do not use the mounting screws provided with the ceilingFloor Mounting Upright Ceiling MountingConnector Panel Access Connecting the DHDConnections to the VX-8d and DHD Controller Controller to the VX-8d11. RS-232 Connection from the DHD Controller to the VX-8d Connecting Source Components to the DHDHdmi Source Connections See Figure Controller13. Component Video Source Connections DTV-Set-Top BoxComputer RGB Camcorder 14. Rgbhv Source ConnectionsGaming Console 15. Scart Rgbs Source ConnectionsComposite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens MotorConnecting an External IR Receiver to the DHDTurning on the Power Connecting to AC PowerInput voltage to the AutoScope lens motor must be between Primary Lens Adjustments Adjusting the Picture OrientationYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation AdjustmentIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Time after turning on the systemInstallation Anamorphic Lens Top View Geometry Using the On-Screen Menus OperationService Main MenuRunco Video Input Source Aspect RatioInput Source Aspect RatioAspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Signal InformationInformation SystemYou must enter a passcode to access the Calibration menu Calibration ISF SettingsCalibration Should be used by ISF-certified technicians onlyColor Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesOperation Copied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation X/y Color Gamut Values ColorOperation 58 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start IR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 DataEnter Specifications VX-8d SpecificationsVX-8d Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions VX-8d Dimensions with Optional Ceiling MountVX-8d/CineWide Dimensions VX-8d/CineWide Dimensions with Optional Ceiling MountVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May
Related manuals
Manual 104 pages 38.93 Kb