Runco VX-8D operation manual Picture

Page 68

Operation

Picture

Picture

Brightness

Contrast

Color

Tint

Sharpness

Noise Filter

Use the controls in the Picture Menu to calibrate each DHD Controller input to achieve optimum picture quality.

The DHD Controller has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Runco video display devices. Accordingly, Runco recommends that setup and calibration be performed by an ISF certified installation technician.

All signal types require separate processing. Therefore, you need to calibrate each DHD Controller input separately.

1. When you change a picture quality setting, save the change to a

Note preset afterwards. Otherwise, the change will be lost when a different input is selected. (Picture quality settings are saved for each input separately.) For information about saving settings, refer to Memory Presets on page 58.

2.For best results, Runco recommends that you set ConstantContrast to Off before adjusting Brightness, Contrast and other image quality settings in this menu (refer to ConstantContrast on page 62). After you have completed the initial calibration, set ConstantContrast to On if desired.

Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Runco recommends using an external test pattern source (Ovation Multimedia, Digital Video Essentials or AVIA test DVD or equivalent) for best results.

Connect your test pattern source to the input that you are calibrating and proceed as follows. Perform the adjustments in the order listed here.

Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2shows a typical PLUGE pattern.

Below Black

Above Black

Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness

52

Runco VX-8d Installation/Operation Manual

Image 68
Contents VX-8d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures Xvi Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-8d at a GlanceExhaust Vent RS-232C Input 9-pin, female D-Sub Power Input 100 to 240 VAC Connect the VX-8d to power hereVX-8d Rear Panel DHD Controller Front Panel Virtual Cinema is available only on the VX-8d/CineWide orDisplay Control DHD Controller RearPanel Inputs 4. USB VX-8d Remote Control Unit DHD Controller/VX-8d Remote ControlOn / OFF Cursor ButtonsInformation about aspect ratios, refer to Table Menu button see below to exit the current menuMemory Preset Buttons Aspect Ratio Selection Buttons169 Letbox LetterboxControls and Functions Installation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Ambient Light Throw DistanceVX-8d Lens Options and Throw Ratios Throw Range Throw Ratio Inches, withLens Option LensCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Synchronization Issues Possible Audio Latency for Various Input TimingsAudio/Video Input Timing Possible Audio Latency millisecondsInstalling the Optional CineWide Lens Mount Other ConsiderationsInstalling the AutoScope Lens Motor VX-8d/CineWide with AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Adjusting the Projection Do not use the mounting screws provided with the ceilingFloor Mounting Upright Ceiling MountingConnector Panel Access Connecting the DHDConnections to the VX-8d and DHD Controller Controller to the VX-8d11. RS-232 Connection from the DHD Controller to the VX-8d Connecting Source Components to the DHDHdmi Source Connections See Figure Controller13. Component Video Source Connections DTV-Set-Top BoxComputer RGB Camcorder 14. Rgbhv Source ConnectionsGaming Console 15. Scart Rgbs Source ConnectionsComposite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens MotorConnecting an External IR Receiver to the DHDInput voltage to the AutoScope lens motor must be between Turning on the PowerConnecting to AC Power Primary Lens Adjustments Adjusting the Picture OrientationYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens ShiftIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Time after turning on the systemInstallation Anamorphic Lens Top View Geometry Using the On-Screen Menus OperationRunco Video ServiceMain Menu Input Source Aspect RatioInput Source Aspect RatioAspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Signal InformationInformation SystemYou must enter a passcode to access the Calibration menu Calibration ISF SettingsCalibration Should be used by ISF-certified technicians onlyColor Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesOperation Copied settings are not retained after a power cycle Copy/PasteInput Names ServiceService Exit Operation X/y Color Gamut Values ColorOperation 58 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyWith Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits IR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 DataEnter VX-8d Specifications SpecificationsVX-8d Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions VX-8d Dimensions with Optional Ceiling MountVX-8d/CineWide Dimensions VX-8d/CineWide Dimensions with Optional Ceiling MountVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May
Related manuals
Manual 104 pages 38.93 Kb