Runco VX-8D operation manual Installing and Adjusting the CineWide Anamorphic Lens

Page 57

Installation

If you are installing a VX-8d/CineWide or VX-8d/CineWide with AutoScope, proceed as follows to install and adjust the anamorphic lens.

It is extremely important that the primary lens is properly

Note adjusted before you install the anamorphic lens. Ensure that the image from the primary lens is perfectly centered on the screen.

The VX-8d Anamorphic lens mount kit consists of everything shown in Figure 3-20.Some components shipped with your projector may differ slightly from what is shown in these instructions. If any items are missing or damaged, please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.

1Lens Adapter Ring and Mounting Screws (3x)

10 Anamorphic Lens

Set Screw

9 Pitch Adjustment

T-Nut (2x)

2 Pitch Adjustment Yoke for Lens

3 Height/Y Adjustment

T-Screw and Washer

(2x)

4 Pitch Adjustment

T-Screw and

Washer (2x)

5 Anamorphic Lens

Holder

8 Yaw/X Adjustment

Lever (2x)

6 1/4-20 Hex Bolt (2x)

and Washer (2x)

7 AutoScope Carriage Plate or Fixed CineWide Base Plate

Figure 3-20. Anamorphic Lens Mounting Assembly - Exploded View

3.10 Installing and Adjusting the CineWide Anamorphic Lens

Anamorphic Lens

Installation and

Adjustment

Runco VX-8d Installation/Operation Manual

41

Image 57

Contents VX-8d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsExternal Control Table of Contents Xiv List of Figures Xvi About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories VX-8d at a Glance Controls and FunctionsExhaust Vent Power Input 100 to 240 VAC Connect the VX-8d to power here VX-8d Rear PanelRS-232C Input 9-pin, female D-Sub Virtual Cinema is available only on the VX-8d/CineWide or DHD Controller Front PanelDHD Controller Rear PanelDisplay Control Inputs 4. USB DHD Controller/VX-8d Remote Control VX-8d Remote Control UnitCursor Buttons On / OFFInformation about aspect ratios, refer to Table Menu button see below to exit the current menuAspect Ratio Selection Buttons Memory Preset Buttons169 Letbox LetterboxControls and Functions Installation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Throw Distance Ambient LightThrow Range Throw Ratio Inches, with VX-8d Lens Options and Throw RatiosLens Option LensFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Possible Audio Latency for Various Input Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Installing the Optional CineWide Lens MountLens Motor VX-8d/CineWide with AutoScope Installing the AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Do not use the mounting screws provided with the ceiling Adjusting the ProjectionFloor Mounting Upright Ceiling MountingConnecting the DHD Connector Panel AccessConnections to the VX-8d and DHD Controller Controller to the VX-8d11. RS-232 Connection from the DHD Controller to the VX-8d Components to the DHD Connecting SourceHdmi Source Connections See Figure ControllerDTV-Set-Top Box 13. Component Video Source Connections14. Rgbhv Source Connections Computer RGB Camcorder15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRTurning on the Power Connecting to AC PowerInput voltage to the AutoScope lens motor must be between Adjusting the Picture Orientation Primary Lens AdjustmentsYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation AdjustmentIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusService Main MenuRunco Video Aspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Information SignalInformation SystemCalibration ISF Settings You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation Color X/y Color Gamut ValuesOperation 58 and ISF Day/Night Memory Presets Operation Lamp Replacement Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter Specifications VX-8d SpecificationsVX-8d Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions with Optional Ceiling Mount VX-8d DimensionsVX-8d/CineWide Dimensions with Optional Ceiling Mount VX-8d/CineWide DimensionsVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May

Related manuals

Manual 104 pages 38.93 Kb