Runco VX-8D operation manual Turning on the Power, Connecting to AC Power

Page 55

Installation

Projector/DHD Controller: Plug the female end of one power cord into the AC		Connecting to AC Power
receptacle on the rear of the VX-8d (AC 100V ~ 240V). Then, connect the other end to
your AC power source.
Similarly connect the DHD Controller to a nearby AC outlet.
AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power
cord is provided for the lens motor. Plug the female end of the AC power cord into the AC
input on the rear of the lens motor assembly. Connect the other end to a 110 VAC power
source.
Caution	The input voltage to the AutoScope lens motor must be between
	100 and 120 VAC. Do not connect the AutoScope lens motor

to a 200-240 VAC power source!

1.Turn on your source components.

2.Turn on the main power switch at the rear of the projector.

3.Turn on the main power switch at the rear of the DHD Controller.

4.If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input.

5.Press the ON button on the remote control (or the ON/STANDBY ( ) button on DHD Controller front panel) to turn on the system. The vacuum fluorescent display on the DHD Controller front panel briefly displays “Initializing System,” followed by “Starting VX-8d.”

6.When the projector is ready for use, the fluorescent display indicates the active source, input resolution/frame rate and aspect ratio; for example:

Current

Source

3.7

Turning on the Power

	VX-8d			HDMI 1
16:9				1080i/60


Aspect Ratio				Input Resolution/Frame Rate

Runco VX-8d Installation/Operation Manual

39

Image 55

Contents VX-8d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures Xvi About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories VX-8d at a Glance Controls and FunctionsExhaust Vent VX-8d Rear Panel Power Input 100 to 240 VAC Connect the VX-8d to power hereRS-232C Input 9-pin, female D-Sub Virtual Cinema is available only on the VX-8d/CineWide or DHD Controller Front PanelPanel DHD Controller RearDisplay Control Inputs 4. USB DHD Controller/VX-8d Remote Control VX-8d Remote Control UnitMenu button see below to exit the current menu On / OFFCursor Buttons Information about aspect ratios, refer to TableLetbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 169Controls and Functions Remote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Throw Distance Ambient LightLens VX-8d Lens Options and Throw RatiosThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input Timings Audio/VideoOther Considerations Installing the Optional CineWide Lens MountLens Motor VX-8d/CineWide with AutoScope Installing the AutoScopeInstalling the Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate VX-8d/CineWide Ceiling Mounting Adjusting the ProjectionDo not use the mounting screws provided with the ceiling Floor Mounting UprightController to the VX-8d Connector Panel AccessConnecting the DHD Connections to the VX-8d and DHD Controller11. RS-232 Connection from the DHD Controller to the VX-8d Controller Connecting SourceComponents to the DHD Hdmi Source Connections See FigureDTV-Set-Top Box 13. Component Video Source Connections14. Rgbhv Source Connections Computer RGB Camcorder15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerInput voltage to the AutoScope lens motor must be between Focus Zoom Vertical and Horizontal Lens Shift Primary Lens AdjustmentsAdjusting the Picture Orientation You must enter a passcode to access the Service menuAnamorphic Lens Installation Adjustment Installing and Adjusting the CineWide Anamorphic LensIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusMain Menu ServiceRunco Video Aspect Ratio Input SourceAspect Ratio Input SourceHdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets System SignalInformation InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF Settings CalibrationColor Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsOperation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation Color X/y Color Gamut ValuesOperation 58 and ISF Day/Night Memory Presets Operation Lamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerEnter VX-8d Specifications SpecificationsVX-8d Specifications Limited Warranty Home Theater Calibration SpecificationsIndustry-Standard Specifications Weight without lensDHD Controller Specifications DHD Controller SpecificationsVX-8d Dimensions with Optional Ceiling Mount VX-8d DimensionsVX-8d/CineWide Dimensions with Optional Ceiling Mount VX-8d/CineWide DimensionsVX-8d/CineWide with AutoScope Dimensions VX-8d/CineWide with AutoScope DimensionsSupported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsPAL-B/G/H/I PAL-M Specifications Page 020-0965-01 Rev. B May

Related manuals

Manual 104 pages 38.93 Kb