Required Settings for HDMI Connection
Setting HDMI Video Output
nMake HDMI Output Signal and HDMI Control Function Settings
“HDMI Setup” (vpage 25, 26)
nMake the Video Output Signal Setting for the Connected Television
“Video Setup” (vpage 26)
nAbout HDMI Video Resolution Setting
•Change the HDMI video resolution by pressing HDMI RESOLUTION button. Switch the output mode as follows. Default settings are underlined.
|
| Auto |
| Bron direct |
|
| 480/576i |
|
|
| 480/576P |
|
| |||||
|
| (Auto) | (Source Direct) | (480/576 interlaced) |
| (480/576 progressive) |
| |||||||||||
|
| 1080P24 |
|
| 1080P |
|
|
| 1080i |
|
|
|
| 720P |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
(1080 progressive, | (1080 progressive) |
| (1080 interlaced) | (720 progressive) |
•If the HDMI resolution is not set to “Auto”, set it to correspond with the resolution of your television. Images will not be projected normally if the television resolution and UD9004’s output resolution do not match.
•Audio and video will be temporarily interrupted if the power of the connected device currently playing back is turned off, or input is switched.
•When you change the HDMI video resolution of the UD9004, it takes from a few seconds up to about 10 seconds for validation between the UD9004 and the connected device. Audio/video is not output during this period.
•When outputting deep colour or 1080p, etc., we recommend you use High Speed HDMI cable for enhanced
NOTE
When the HDMI video resolution is set to “1080P24”, HDMI video signals are output from the UD9004 with a resolution of 1080P and a frame rate of 24 frames per second, regardless of the video signals on the disc being played. Because of this, when playing discs containing video signals recorded with a frame rate of something other than 24 frames per second, the movement of the picture may be unnatural. If this happens, set the HDMI video resolution to something other than “1080P24”.
ENGLISH
1. Home Theater Playback – Playing Back Using
Setting HDMI Audio Output
•When you press SET UP button and set “HDMI Setup” – “Audio Setup” to “Auto” (vpage 25) on the GUI menu, audio mode is set according to the connected device.
•When you want to set the HDMI audio output separately, change according to the following table.
•Refer to the owner’s manual of the connected device regarding HDMI audio input speci compatible with the connected device.
Device to be connected Setting items | About output signal and speaker settings | ||||||
|
|
|
|
|
| ||
Device with the following |
| UD9004 outputs a bitstream signal that is decoded by the | |||||
| connected device. | ||||||
|
|
| |||||
|
|
| b In this case, you cannot make a speaker setting for HDMI | ||||
· Dolby TrueHD |
|
|
| ||||
|
|
| audio with the UD9004. | ||||
· Dolby Digital Plus |
|
| Auto | ||||
|
| Make the setting with the connected device. | |||||
· Dolby Digital |
|
|
| ||||
|
|
| b When outputting the Dolby TrueHD or | ||||
· |
|
|
| ||||
|
|
| press MODE button and set “BD Audio Mode” to “HD | ||||
· DTS |
|
|
|
| |||
|
|
|
| Audio Output” (vpage 33). | |||
|
|
|
|
| |||
|
|
|
|
| Outputs | ||
|
|
|
|
| speaker setting by the UD9004. | ||
|
|
|
|
| b For speaker setting, on the GUI menu, “Audio Setup” | ||
|
|
|
|
| – “7.1ch Audio Out” – “Multi Channel” – “Speaker | ||
Device | compatible | with |
| Con” ( | vpage 27). | ||
|
|
| |||||
Multi LPCM |
|
| |||||
input, but not capable | of | To output sound from a disc while maintaining the same | |||||
BM On | |||||||
speaker | setting for | each | |||||
| sound quality as the disc sound, some settings of Audio | ||||||
channel |
|
|
|
| |||
|
|
|
| Setup are disabled as default (vpage 25 ~ 27). | |||
|
|
|
|
| |||
|
|
|
|
| To enable the settings of Audio Setup, set Source Direct | ||
|
|
|
|
| to “Off” (vpage 26). | ||
|
|
|
|
| b BM : Bass Management (means | ||
|
|
|
|
| setting) |
| |
Device | compatible | with |
| Output of | |||
Multi LPCM | UD9004. |
| |||||
input, | and capable | of | Perform the speaker setting with the connected device. | ||||
BM Off | |||||||
speaker | setting for | each | b BM : Bass Management (means | ||||
| |||||||
channel |
|
|
|
| setting) |
| |
Device compatible with 2- |
| Downmixed | |||||
2ch | from the UD9004. | ||||||
channel HDMI audio input | |||||||
| Perform the speaker setting with the connected device. | ||||||
|
|
|
|
| |||
|
|
|
|
| Audio signal are not output from the UD9004’s HDMI | ||
Device not compatible with | Mute | terminal. |
| ||||
HDMI audio signal input |
| Only video signals are output from the HDMI terminal. | |||||
|
| ||||||
|
|
|
|
| b Make the audio connection. |
Getting Started Connections Setup Playback HDMI Control Function Information Troubleshooting Speci
15