| Setting items |
| Setting contents | |||
Source Direct |
|
|
| Off : Enable the speaker and subwoofer settings. | ||
Disable the | speaker | and | On : 50kHz : Output the disc contents as is. When playing Super Audio | |||
subwoofer | settings | and | CD, output up to 50 kHz audio signals. | |||
output the disc audio as is. | On : 100kHz : Output the disc contents as is. When playing Super Audio | |||||
NOTE |
|
|
|
| CD, output up to 100 kHz audio signals with DSD format. | |
|
|
|
|
| ||
Set to within the playback | • Setting “On: 50 kHz” or “On: 100 kHz” enables | |||||
frequency | band | of | the | |||
ampli |
|
|
|
|
| all channels recommended for DTS. (Note that this results in a 5 dB |
“On” at “50 kHz” or “100 | increase in subwoofer volume, and a 15 dB increase with Super Audio | |||||
kHz”. | Setting | outside the | CD). This also allows you to play back the | |||
frequency | band can | result | Audio recorded on all channels with the full frequency range. In this | |||
in damage to your ampli | case, make an analog connection according to disc operating manual. | |||||
and even |
|
|
|
| • When set to “On: 50 kHz” or “On: 100 kHz”, all speaker sizes are set to | |
|
|
|
|
|
| “Large” and “Yes” is set for the subwoofer. |
|
|
|
|
|
| • Even when set to “On: 50 kHz” or “On: 100 kHz”, “Channel Level” and |
|
|
|
|
|
| “Distance” settings are available. |
Compression |
|
|
| Auto : Automatically compress Dolby TrueHD audio dynamic range. The | ||
Compresses | the | dynamic | sound is not compressed when playing signals other than Dolby TrueHD | |||
range | of | Dolby | TrueHD/ | signals. | ||
Dolby | Digital/Dolby Digital | Off : Dynamic Range compression is not applied. | ||||
Plus audio. At night or other | Low : Set minimum dynamic range compression. | |||||
times when you cannot play | Middle : Set middle dynamic range compression. | |||||
back at high volume, this | High : Set maximum dynamic range compression. | |||||
compensates | by | reducing |
| |||
high | level | sounds | and |
| ||
increasing low level sounds. |
| |||||
AFDM |
|
|
|
|
| On : Automatically set surround mode when the ID signal is included. |
Automatically | set | the | Off : Do not set surround mode even when the ID signal is included. | |||
surround mode by detecting | MTRX : Create a surround audio signal by matrix processing, regardless | |||||
the | surround |
| mode | of the presence of an ID signal. | ||
identi |
|
|
|
|
|
|
in the disc.
An EX
“AFDM” set to “On”, set to “MTRX” in case the playback mode does not automatically switch.
NOTE
•This setting is valid when “Audio Setup” – “7.1ch Audio Out” on the GUI menu is set to (vpage 32) and when “HDMI Setup” – “Audio Setup” on the GUI menu is set to “Multi LPCM BM On” (vpage 25).
•This setting is invalid when “Audio Setup” – “Source Direct” on the GUI menu is set to “On” (vpage 29).
•This function is invalid for the
ENGLISH
Audio Setup
| Setting items | Setting contents | |
BD Effect Sound | On : Outputs BD effect sound. | ||
Sets for a click sound and | Off : Does not output BD effect sound. | ||
other | outputs during BD |
| |
popup menu operations. |
| ||
|
| ||
BD | Auto : Outputs primary audio (main audio) in the same type of audio | ||
Sets | the format during | format. Dolby Digital/Dolby Digital Plus/Dolby TrueHD are output as | |
output of the BD’s Mix Audio | Dolby Digital, | ||
signal from the digital output | as Linear PCM. | ||
terminal. | Dolby Digital : Outputs to the digital audio output terminal (optical/ | ||
|
| coaxial) with Dolby Digital. | |
|
| DTS : Outputs to the digital audio output terminal (optical/coaxial) with | |
|
| DTS. | |
|
| Valid when “BD Audio Mode” is set to “Mix Audio Output” (vpage | |
|
| 33). | |
Digital Out | Bitstream : Outputs a bitstream signal. Converts Dolby TrueHD, Dolby | ||
Set the audio signal of digital | Digital Plus to Dolby Digital, and | ||
audio output. | PCM : Output the downmixed audio signal to 2ch LPCM. | ||
For more information on each | PCM Down Sampling : Convert sampling frequency audio greater than | ||
audio signal, refer to “Audio | 48 kHz to a 48 kHz 2ch LPCM audio output signal. | ||
Signal from the Digital Audio |
| ||
Output | (Optical/Coaxial) | • When outputting CD, etc. to a digital recording device such as the CD | |
Terminal” (vpage 17). | |||
recorder, convert to PCM or PCM down sampling. | |||
|
| ||
|
| • When a disc with recorded Linear PCM or PPCM (Packed PCM) is played | |
|
| back, this outputs Linear PCM irrespective of the setting. | |
Downmix | Lt/Rt : Signals are converted to Dolby Surround compatible | ||
Set the method used to | audio signals for output. This setting is valid for | ||
convert a | Surround, Dolby Digital Plus and Dolby Digital audio signals. (If the | ||
audio signal to a | connected AV Amp is Dolby Pro Logic compatible, AV Amp plays back | ||
signal. |
| using surround audio.) |
Stereo : Outputs by converting to the 2ch (stereo) audio.
NOTE
In order to enable the “Lt/Rt” setting when playing back BD, set “BD
Audio Mode” to “HD Audio Output” (vpage 33).
Getting Started Connections Setup Playback HDMI Control Function Information Troubleshooting Speci
Remote control operation | SET UP | :Displaying the menu | d f 0 1 | :Moves the cursor | ENTER :Decision the setting | RETURN :Return to previous menu | 29 |
buttons |
| Cancel the menu |
| (Up/Down/Left/Right) |
|
|