Audio Setup, Set Up, Enter | Marantz UD9004 instruction

Getting Started Connections Setup Playback HDMI Control Function Information Troubleshooting Speci

ENGLISH

Audio Setup

Setting items

Setting contents

Setting items

Setting contents

7.1ch Audio Out

GCrossover Freq.H : Set the upper limit of the low frequency signals

7.1ch Audio Out

n Channel Level : Set the volume of the test tone to be the same when

output from the subwoofer.

it is output from each speaker.

• 40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz

GModeH : Select a test tone output method.

Outputs at

below set frequency, each

speaker’s

bass signal

• Auto : Automatically switch the test tone output speaker.

output from the subwoofer. Set this according to the low frequency

• Manual : Manually switch the test tone output speaker.

reproduction capabilities of the speakers you are using.

• Advanced : Set the low frequency signals to be output from the

GStartH : Begin outputting the test tone.

signals of the respective speakers to the subwoofer.

Front L / Center / Front R / Surround R /

Front, Center, Surround, Surr. Back

Surr. Back R / Surr. Back L / Surround L / Subwoofer

40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz

b When the test tone output stops, press RETURN button.

LFE / LFE+Main

GSW +10dBH : Increase the subwoofer output level by 10 dB. z

80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz

• Off : Do not change the subwoofer output level.

When, on the GUI menu, “Audio Setup” – “7.1ch Audio Out”– “Multi

• On : Increase the subwoofer output level by +10 dB.

GDefaultH : Reset all channel level settings to factory default.

Channel” – “Speaker Con” – “Subwoofer” is set to “Yes”

(vpage 27), you can select “LFE” or “LFE+Main”.

• No : Do not Reset.

NOTE

• Yes : Reset.

n Distance : Set the distance between the listening position and each

• Select “Large” or “Small” not according to the physical size of the

speaker.

speaker but according to the low frequency reproduction capabilities

GFeetH or GMetersH : Set the unit of distance.

based on the frequency set at “Crossover Freq.”.

• On the GUI menu, if the “Audio Setup” – “7.1ch Audio Out”– “Multi

GStepH : Set the minimum variable width of the distance.

Channel” – “Speaker Con” item setting is changed, other

1ft, 0.1ft, 0.1m, 0.01m

settings are automatically changed as well.

GExampleH

GDefaultH : Reset all distance settings to factory default.

If you set “Front” to “Small”, “Subwoofer” is set to “Yes” and “Large”

Front L / Front R / Center / Subwoofer / Surround L / Surround R /

cannot be selected for “Center”, “Surround” and “Surr. Back”.

Surr. Back L / Surr. Back R : Select the speaker you want to set,

• Audio signal

(sampling frequency, number

of channels) from the

and set the distance. Set the value that is closest to the measured

HDMI output terminal may be restricted by the speci

distance.

HDMI audio that can be input by the device at the other side.

0~60ft or 0~18m

GExampleH

If the HDMI audio speci

5.1 channel, even when UD9004 plays back by the 7.1 channel, the

• Default settings :

5.1 channel audio is automatically output. In that case, the analog

Front/Center/Subwoofer : 3.6 meters (12 feet)

audio output becomes the 5.1 channel output as well.

Surround/Surr. Back : 3.0 meters (10 feet)

• Set the difference in the distance betweem the speakers to less than

6.0 meters (20 feet).

Subwoofer Mode

LFE : Add the low frequency signal of the channel for which the speaker

Set the type of low frequency

size is set to “small” to the subwoofer signal and output it.

signal to be output from the LFE+Main : Add the low frequency signal of all channels to the subwoofer

subwoofer.

signal and output it.

z : “SW +10dB” cannot be set for “HDMI Setup” – “Audio Setup” – “Multi LPCM BM On” – “Channel

Level” on the GUI menu.

Remote control operation

SET UP

:Displaying the menu

d f 0 1

:Moves the cursor

ENTER

:Decision the setting

RETURN :Return to previous menu

buttons

Cancel the menu

(Up/Down/Left/Right)