Panasonic AW-RP50N Selecting the control items pan, tilt, zoom and focus, FOCUS/IRIS Standard

Page 20

Setting the functions

Settings when the remote camera moves horizontally or vertically during tele shooting

During tele shooting, the remote camera’s pan/tilt operation are slowed down to make positioning easier.

Note

This function takes effect when the unit is connected to the AW-HE50. It does not work with any other models.

From the [SETUP] menu, select [OPERATE] and display [SPEED WITH Z]. Then set the movement speed.

5.SPEED WITH Z Off

On: The speed at which the remote camera moves is reduced.

Off: The remote camera moves at the normal speed.

Switching from focus control to iris control or vice versa

It is possible to switch the control, which is implemented by dial and button operations, from focus control to iris control (or vice versa).

 

1

2

3

4

5

IRIS

AUTO

CAMERA STATUS / SELECTION

 

 

 

 

 

AUTO

 

 

 

 

TELE

 

 

 

 

 

ZOOM

 

 

 

LOW

HI

 

WIDE

 

 

 

FOCUS/PUSH OTAF

PTZ/FOCUS SPEED PA

From the [SETUP] menu, select [OPERATE] and display [FOCUS/IRIS]. Then select either “STANDARD” or “EXCHANGE”.

7.FOCUS/IRIS

STANDARD

When “EXCHANGE” is selected as the setting, focus control and iris control are switched.

When “STANDARD” is selected, the original control is restored.

Selecting the control items (pan, tilt, zoom and focus)

Select the control items for the currently selected remote camera.

From the [SETUP] menu, select [OPERATE] and display [SPEED TARGET]. Then select the control item.

6.SPEED TARGET

P/T/Z/F

P/T/Z/F:

The operation speed setting takes effect for panning, tilting, zooming and focusing.

P/T:

The operation speed setting takes effect for panning and tilting.

Setting the PAN/TILT lever inclination and speed

The correlation between angle and operating speed when the PAN/TILT lever is inclined can be adjusted.

From the [SETUP] menu, select [OPERATE] and display [P/T CURV]. Then set the correlation between the lever angle and its operating speed.

8.P/T CURV

▲

1

 The higher the value selected, the slower the operating speed.

Operating speed

Inclination of lever

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operating Instructions Contents Before use How to turn the power of the remote cameras on and off How to turn the power of the remote cameras onHow to turn the power of the remote cameras off CAM Power Group OFFTurn the F2 dial to select OFF, and press Turn the F2 dial to select ALL OFF, and press the F2 dialSetting and operating the preset memories Preset numbers and registered pagesPreset number Number  Memo Executing the preset data Deleting the preset memory dataPRESET1 PAGE1Setting the pedestal Selecting the settings for a selected remote cameraSetting the gain Setting the white balance Set the Preset MEMORY/MENU 4 button AWB/ABB to onTurn the F1 dial to select the white balance mode Selecting the white balance modeAWB MOD AWB a SET AWB Automatically adjusting the white balanceTurn the F2 dial to select AWB, and press Set the Preset MEMORY/MENU 2 button R/BGAIN to on Turn the F1 dial to select ATWRgain BgainTurn the F2 dial to select ABB, and press Setting the black balanceSet the Preset MEMORY/MENU 3 button R/BPED to on Setting the shutter speed Setting the detailSet the Preset MEMORY/MENU 5 button Shutter to on Turn the F1 dial to select the shutter modeSetting the shooting mode Set the Preset MEMORY/MENU 7 button SCENE/MODE to onTurn the F1 dial to select the shooting mode Specifying the color barsRemote camera Menu ON/OFF Dial operation Menu operation Operating the menu items of the selected remote cameraTable of operations Registering functions User buttons Setting the User buttonsSet the Preset MEMORY/MENU 9 button Setup to on Tally settings 3TALLYTally OUT OffSetting the functions Turn the F1 dial to select the target menu itemFocus DIR Normal Setting the remote camera operationsZoom DIR Normal Setting the PAN/TILT lever inclination and speed Selecting the control items pan, tilt, zoom and focusFOCUS/IRIS Standard Speed TargetScope Mode a Mode Operations performedReturning the remote cameras to their home position Diag SpeedSetting the upper limit Setting the lower limitWhen the AW-HE50 is used When any other remote camera is usedSetting the left limit Setting the right limit6FUNCTION Preset CTL1 Adjusting the minimum lens zoom start speedExercising external control over the preset memory data Adjusting the LCD panel backlight Menu Control EnableLocking the button operations 9LCD BLSetting linkup with the switcher Switcher network settingsSet Preset MEMORY/MENU 10 button System to on Press the Exit buttonLink setting 2SW LinkSwlink Off Swlink On4SW Assign Setting the image output and image inputTurn the F1 dial to select the input line of the switcher Switcher settings Buscont Off Bus switchingTurn the F1 dial to select the menu item to be set Buscont OffFasist Off BUS AUXCamsel Off Self Tallyip OffT Lever Setting for the information to be displayed on the OSD Setting all the information displaysTogether Turn the F1 dial to and select the menu item to be setSetting each information item to be displayed Checking the equipment alarm information Select Power10ALARM Select CAM1 to CAM100Returning the unit to its factory status Turn the F2 dial to select the initializing modePress the F2 dial to initialize the settings Control interface for external devices Sub 15-pin, female, inch threadExample of GPI OUT connections Current Max mA AW-RP50IP settings Setup SoftwareInstalling the software Displaying the Setting tab Auto IP setting Changing the IP addressesChanging the camera numbers Initializing the IP addressesLoading the setting files Saving the setting filesSaving and loading data Saving the log filesReferencing the network environment Enter the IP addresses in the AW-RP50 IP Address boxesButton Menu item Control device Initial value Setting Table of menu items0dB to 12dB 1 step AW-HE50Video Buscont Option AW-HE50 Display only F0610Y1070 D
Related manuals
Manual 82 pages 17 Kb

AW-RP50N specifications

The Panasonic AW-RP50N is a sophisticated remote camera controller designed for professional video production environments. Renowned for its advanced features and versatility, the AW-RP50N serves as an essential tool for operators needing precise control over multiple cameras in real-time.

One of the standout characteristics of the AW-RP50N is its ability to control up to 200 Panasonic cameras simultaneously. This feature is particularly beneficial in large-scale productions, such as broadcasting events, live concerts, and sports. It not only enhances operational efficiency but also provides cinematographers with a centralized point for camera management.

The AW-RP50N boasts a user-friendly interface, equipped with a large LCD touch panel that allows easy navigation and adjustment of camera settings. The intuitive layout makes it simple for operators to switch between camera feeds, adjust PTZ (pan-tilt-zoom) settings, and monitor video feeds without interruption. Customizable settings enable users to tailor the interface to suit their workflow preferences.

In terms of technology, the AW-RP50N supports multiple communication protocols, including IP (Internet Protocol) and serial communication. This flexibility allows integration with various camera models and third-party systems, offering a cohesive control experience. The unit is designed with robustness in mind, ensuring reliability even in demanding environments.

The AW-RP50N features advanced zoom and focus controls, providing smooth and precise movements essential for capturing high-quality video content. With programmable presets, operators can save specific camera angles and settings, making it easy to quickly switch back to preferred positions during production.

Additionally, it supports HD/SD video formats, catering to diverse production needs. The unit's compact design also makes it an ideal choice for mobile setups and small production teams that require portability without sacrificing performance.

Overall, the Panasonic AW-RP50N remote camera controller is a remarkable piece of technology, combining scalability, ease of use, and high-performance capabilities. Its robust feature set makes it an indispensable asset for professionals in the broadcasting and production industry, ensuring dynamic and reliable control of remote cameras in any situation. Whether scaling a large production or managing a small shoot, the AW-RP50N enables creators to achieve their artistic vision with precision and ease.
Top Page Image Contents