Panasonic AW-RP50N Executing the preset data, Deleting the preset memory data, PRESET1, PAGE1

Page 7

Setting and operating the preset memories

Executing the preset data

1 Press one of the CAMERA STATUS/SELECTION buttons 1 to 5 to select the remote camera to be operated.

Select the remote camera which is to be pointed at the camera angle registered in the preset memory.

2 After pressing the PAGE button, press the

PRESET MEMORY/MENU button to specify the registered “Page number” of the preset memory.

In this step, specify the registered “Page number” of the preset memory.

 For details on the relationship between the “Preset number”, “Page number” and “Number on the page”, refer to the section entitled <Preset numbers and registered pages>.

3 Press the PRESET MEMORY/MENU button to specify the “Number on the page”.

The preset memory data is executed at the same time as the “Number on the page” are specified.

 

2

 

 

2,3

 

 

 

 

 

 

1

2

3

4

5

 

 

MENU

PAGE

GAIN/PED

R/B GAIN

R/B PED

AWB/ABB

SHUTTER

F2

EXIT

 

 

6

7

8

9

10

 

 

STORE

DELETE

DETAIL

SCENE/MODE

CAMERA

SETUP

SYSTEM

USER1

USER2

 

 

 

PRESET MEMORY / MENU

 

 

 

 

 

1

2

3

4

5

 

 

IRIS

AUTO

 

CAMERA STATUS / SELECTION

 

 

PT ACTIVE

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 When the preset memory data is executed, the preset number is displayed on the right side of the top level of the LCD panel.

PRESET1

PAGE:1 (1-10)

The preset number display is cleared when the power of the unit or remote camera has been turned off or when the camera group has been switched.

 In the case of the AW-HE50, the corresponding PRESET MEMORY/MENU button will go off, and then it will light again when preset memory data is executed.

In the case of another remote camera connected serially, the corresponding PRESET MEMORY/MENU button will simply just light.

Deleting the preset memory data

Note

This function does not work with the AW-PH400.

1 Press one of the CAMERA STATUS/SELECTION buttons 1 to 5 to select the remote camera to be operated.

Select the remote camera whose preset memory data is to be deleted.

2 Press the DELETE button.

3 After pressing the PAGE button, press the

PRESET MEMORY/MENU button to specify the “Page number” of the preset memory data to be deleted.

In this step, specify the “Page number” of the preset memory data to be deleted.

 For details on the relationship between the “Preset number”, “Page number” and “Number on the page”, refer to the section entitled <Preset numbers and registered pages>.

4 Hold down the PRESET MEMORY/MENU button to specify the “Number on the page”.

The preset memory data is deleted at the same time as the “Number on the page” is specified.

Note

When specifying the “Number on the page”, hold down the PRESET MEMORY/MENU button.

 

3

 

 

3, 4

 

 

 

 

 

 

1

2

3

4

5

 

 

MENU

PAGE

GAIN/PED

R/B GAIN

R/B PED

AWB/ABB

SHUTTER

F2

EXIT

 

 

6

7

8

9

10

 

 

STORE

DELETE

DETAIL

SCENE/MODE

CAMERA

SETUP

SYSTEM

USER1

USER2

 

 

 

PRESET MEMORY / MENU

 

 

 

 

 

1

2

3

4

5

 

 

IRIS

AUTO

 

CAMERA STATUS / SELECTION

 

 

PT ACTIVE

 

 

 

 

 

 

 

2

 

 

1

 

 

 

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operating Instructions Contents Before use How to turn the power of the remote cameras on How to turn the power of the remote cameras on and offTurn the F2 dial to select ALL OFF, and press the F2 dial How to turn the power of the remote cameras offCAM Power Group OFF Turn the F2 dial to select OFF, and press Memo  Setting and operating the preset memoriesPreset numbers and registered pages Preset number NumberPAGE1 Executing the preset dataDeleting the preset memory data PRESET1Setting the gain Selecting the settings for a selected remote cameraSetting the pedestal Selecting the white balance mode Setting the white balanceSet the Preset MEMORY/MENU 4 button AWB/ABB to on Turn the F1 dial to select the white balance modeTurn the F2 dial to select AWB, and press Automatically adjusting the white balanceAWB MOD AWB a SET AWB Bgain Set the Preset MEMORY/MENU 2 button R/BGAIN to onTurn the F1 dial to select ATW RgainSet the Preset MEMORY/MENU 3 button R/BPED to on Setting the black balanceTurn the F2 dial to select ABB, and press Turn the F1 dial to select the shutter mode Setting the shutter speedSetting the detail Set the Preset MEMORY/MENU 5 button Shutter to onSpecifying the color bars Setting the shooting modeSet the Preset MEMORY/MENU 7 button SCENE/MODE to on Turn the F1 dial to select the shooting modeTable of operations Operating the menu items of the selected remote cameraRemote camera Menu ON/OFF Dial operation Menu operation Set the Preset MEMORY/MENU 9 button Setup to on Setting the User buttonsRegistering functions User buttons Off Tally settings3TALLY Tally OUTTurn the F1 dial to select the target menu item Setting the functionsZoom DIR Normal Setting the remote camera operationsFocus DIR Normal Speed Target Setting the PAN/TILT lever inclination and speedSelecting the control items pan, tilt, zoom and focus FOCUS/IRIS StandardDiag Speed Scope Mode aMode Operations performed Returning the remote cameras to their home positionWhen any other remote camera is used Setting the upper limitSetting the lower limit When the AW-HE50 is usedSetting the right limit Setting the left limit6FUNCTION Exercising external control over the preset memory data Adjusting the minimum lens zoom start speedPreset CTL1 9LCD BL Adjusting the LCD panel backlightMenu Control Enable Locking the button operationsPress the Exit button Setting linkup with the switcherSwitcher network settings Set Preset MEMORY/MENU 10 button System to onSwlink On Link setting2SW Link Swlink OffTurn the F1 dial to select the input line of the switcher Setting the image output and image input4SW Assign Buscont Off Switcher settingsBuscont Off Bus switching Turn the F1 dial to select the menu item to be setCamsel Off BUS AUXFasist Off T Lever Tallyip OffSelf Turn the F1 dial to and select the menu item to be set Setting for the information to be displayed on the OSDSetting all the information displays TogetherSetting each information item to be displayed Select CAM1 to CAM100 Checking the equipment alarm informationSelect Power 10ALARMPress the F2 dial to initialize the settings Turn the F2 dial to select the initializing modeReturning the unit to its factory status Current Max mA AW-RP50 Control interface for external devicesSub 15-pin, female, inch thread Example of GPI OUT connectionsInstalling the software Setup SoftwareIP settings Displaying the Setting tab Initializing the IP addresses Auto IP settingChanging the IP addresses Changing the camera numbersSaving the log files Loading the setting filesSaving the setting files Saving and loading dataEnter the IP addresses in the AW-RP50 IP Address boxes Referencing the network environmentAW-HE50 Button Menu item Control device Initial value SettingTable of menu items 0dB to 12dB 1 stepVideo Buscont Option AW-HE50 Display only F0610Y1070 D
Related manuals
Manual 82 pages 17 Kb

AW-RP50N specifications

The Panasonic AW-RP50N is a sophisticated remote camera controller designed for professional video production environments. Renowned for its advanced features and versatility, the AW-RP50N serves as an essential tool for operators needing precise control over multiple cameras in real-time.

One of the standout characteristics of the AW-RP50N is its ability to control up to 200 Panasonic cameras simultaneously. This feature is particularly beneficial in large-scale productions, such as broadcasting events, live concerts, and sports. It not only enhances operational efficiency but also provides cinematographers with a centralized point for camera management.

The AW-RP50N boasts a user-friendly interface, equipped with a large LCD touch panel that allows easy navigation and adjustment of camera settings. The intuitive layout makes it simple for operators to switch between camera feeds, adjust PTZ (pan-tilt-zoom) settings, and monitor video feeds without interruption. Customizable settings enable users to tailor the interface to suit their workflow preferences.

In terms of technology, the AW-RP50N supports multiple communication protocols, including IP (Internet Protocol) and serial communication. This flexibility allows integration with various camera models and third-party systems, offering a cohesive control experience. The unit is designed with robustness in mind, ensuring reliability even in demanding environments.

The AW-RP50N features advanced zoom and focus controls, providing smooth and precise movements essential for capturing high-quality video content. With programmable presets, operators can save specific camera angles and settings, making it easy to quickly switch back to preferred positions during production.

Additionally, it supports HD/SD video formats, catering to diverse production needs. The unit's compact design also makes it an ideal choice for mobile setups and small production teams that require portability without sacrificing performance.

Overall, the Panasonic AW-RP50N remote camera controller is a remarkable piece of technology, combining scalability, ease of use, and high-performance capabilities. Its robust feature set makes it an indispensable asset for professionals in the broadcasting and production industry, ensuring dynamic and reliable control of remote cameras in any situation. Whether scaling a large production or managing a small shoot, the AW-RP50N enables creators to achieve their artistic vision with precision and ease.
Top Page Image Contents