Panasonic AW-RP50N Returning the remote cameras to their home position, Diag Speed

Page 21

Setting the functions

Setting the speed at which to move to the position set by the preset memory

The speed at which to move to the position where the remote camera has been set to be in the preset memory when the preset operation is conducted can be set.

From the [SETUP] menu, select [PRESET] and display [DIAG SPEED]. Then set the speed.

The higher the setting, the faster the operating speed.

1.DIAG SPEED ▼

1

Returning the remote cameras to their home position

The remote cameras connected can be returned to their home position.

From the [SETUP] menu, select [PRESET] and display [HOME POSITION]. Then press the F2 dial.

3.HOME POSITION▲ SET

Setting the operations to be performed when a preset operation is executed

The operations which the remote camera is to performed when the preset operation is conducted can be set.

From the [SETUP] menu, select [PRESET] and display [SCOPE]. Then set the operations to be performed.

2.SCOPE

MODE A

The operations that the camera performs when a preset operation is executed differ depending on the mode selected.

Mode

Operations performed

 

 

MODE A

Pan, tilt, zoom, focus, iris, gain, white balance

 

 

MODE B

Pan, tilt, zoom, focus, iris

 

 

MODE C

Pan, tilt, zoom

 

 

Note

This function takes effect when the unit is connected to the AW-HE50. It does not work with any other models.

Adjusting the panning, tilting, zooming and focusing speed

The speed is adjusted uniformly for the panning, tilting, zooming and focusing together.

When the PTZ/FOCUS SPEED dial is turned clockwise, the speed is increased; conversely, when it is turned counterclockwise, it is reduced.

 

1

2

3

4

5

IRIS

AUTO

CAMERA STATUS / SELECTION

PT ACTIVE

 

 

 

AUTO

ZOOM

LOW HI

WIDE

FOCUS/PUSH OTAF

PTZ/FOCUS SPEED PAN/TILT

From the [SETUP] menu, select [OPERATE] and display [SPEED TARGET]. If P/T is selected, the speed adjustment is confined to panning and tilting only.

In this case, the zooming and focusing speed is fixed to the speed which was set immediately before P/T was selected.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operating Instructions Contents Before use How to turn the power of the remote cameras on How to turn the power of the remote cameras on and offCAM Power Group OFF How to turn the power of the remote cameras offTurn the F2 dial to select OFF, and press Turn the F2 dial to select ALL OFF, and press the F2 dialPreset numbers and registered pages Setting and operating the preset memoriesPreset number Number  Memo Deleting the preset memory data Executing the preset dataPRESET1 PAGE1Selecting the settings for a selected remote camera Setting the gainSetting the pedestal Set the Preset MEMORY/MENU 4 button AWB/ABB to on Setting the white balanceTurn the F1 dial to select the white balance mode Selecting the white balance modeAutomatically adjusting the white balance Turn the F2 dial to select AWB, and pressAWB MOD AWB a SET AWB Turn the F1 dial to select ATW Set the Preset MEMORY/MENU 2 button R/BGAIN to onRgain BgainSetting the black balance Set the Preset MEMORY/MENU 3 button R/BPED to onTurn the F2 dial to select ABB, and press Setting the detail Setting the shutter speedSet the Preset MEMORY/MENU 5 button Shutter to on Turn the F1 dial to select the shutter modeSet the Preset MEMORY/MENU 7 button SCENE/MODE to on Setting the shooting modeTurn the F1 dial to select the shooting mode Specifying the color barsOperating the menu items of the selected remote camera Table of operationsRemote camera Menu ON/OFF Dial operation Menu operation Setting the User buttons Set the Preset MEMORY/MENU 9 button Setup to onRegistering functions User buttons 3TALLY Tally settingsTally OUT OffTurn the F1 dial to select the target menu item Setting the functionsSetting the remote camera operations Zoom DIR NormalFocus DIR Normal Selecting the control items pan, tilt, zoom and focus Setting the PAN/TILT lever inclination and speedFOCUS/IRIS Standard Speed TargetMode Operations performed Scope Mode aReturning the remote cameras to their home position Diag SpeedSetting the lower limit Setting the upper limitWhen the AW-HE50 is used When any other remote camera is usedSetting the right limit Setting the left limit6FUNCTION Adjusting the minimum lens zoom start speed Exercising external control over the preset memory dataPreset CTL1 Menu Control Enable Adjusting the LCD panel backlightLocking the button operations 9LCD BLSwitcher network settings Setting linkup with the switcherSet Preset MEMORY/MENU 10 button System to on Press the Exit button2SW Link Link settingSwlink Off Swlink OnSetting the image output and image input Turn the F1 dial to select the input line of the switcher4SW Assign Buscont Off Bus switching Switcher settingsTurn the F1 dial to select the menu item to be set Buscont OffBUS AUX Camsel OffFasist Off Tallyip Off T LeverSelf Setting all the information displays Setting for the information to be displayed on the OSDTogether Turn the F1 dial to and select the menu item to be setSetting each information item to be displayed Select Power Checking the equipment alarm information10ALARM Select CAM1 to CAM100Turn the F2 dial to select the initializing mode Press the F2 dial to initialize the settingsReturning the unit to its factory status Sub 15-pin, female, inch thread Control interface for external devicesExample of GPI OUT connections Current Max mA AW-RP50Setup Software Installing the softwareIP settings Displaying the Setting tab Changing the IP addresses Auto IP settingChanging the camera numbers Initializing the IP addressesSaving the setting files Loading the setting filesSaving and loading data Saving the log filesEnter the IP addresses in the AW-RP50 IP Address boxes Referencing the network environmentTable of menu items Button Menu item Control device Initial value Setting0dB to 12dB 1 step AW-HE50Video Buscont Option AW-HE50 Display only F0610Y1070 D
Related manuals
Manual 82 pages 17 Kb

AW-RP50N specifications

The Panasonic AW-RP50N is a sophisticated remote camera controller designed for professional video production environments. Renowned for its advanced features and versatility, the AW-RP50N serves as an essential tool for operators needing precise control over multiple cameras in real-time.

One of the standout characteristics of the AW-RP50N is its ability to control up to 200 Panasonic cameras simultaneously. This feature is particularly beneficial in large-scale productions, such as broadcasting events, live concerts, and sports. It not only enhances operational efficiency but also provides cinematographers with a centralized point for camera management.

The AW-RP50N boasts a user-friendly interface, equipped with a large LCD touch panel that allows easy navigation and adjustment of camera settings. The intuitive layout makes it simple for operators to switch between camera feeds, adjust PTZ (pan-tilt-zoom) settings, and monitor video feeds without interruption. Customizable settings enable users to tailor the interface to suit their workflow preferences.

In terms of technology, the AW-RP50N supports multiple communication protocols, including IP (Internet Protocol) and serial communication. This flexibility allows integration with various camera models and third-party systems, offering a cohesive control experience. The unit is designed with robustness in mind, ensuring reliability even in demanding environments.

The AW-RP50N features advanced zoom and focus controls, providing smooth and precise movements essential for capturing high-quality video content. With programmable presets, operators can save specific camera angles and settings, making it easy to quickly switch back to preferred positions during production.

Additionally, it supports HD/SD video formats, catering to diverse production needs. The unit's compact design also makes it an ideal choice for mobile setups and small production teams that require portability without sacrificing performance.

Overall, the Panasonic AW-RP50N remote camera controller is a remarkable piece of technology, combining scalability, ease of use, and high-performance capabilities. Its robust feature set makes it an indispensable asset for professionals in the broadcasting and production industry, ensuring dynamic and reliable control of remote cameras in any situation. Whether scaling a large production or managing a small shoot, the AW-RP50N enables creators to achieve their artistic vision with precision and ease.
Top Page Image Contents