Wolf Appliance Company DCL-200FD manual Aim, Remote at, ProScaler IR, Button to turn on

Page 13

ProScalerHigh Definition Video Processor User’s Manual

Note: Wolf Cinema always recommends that you, your custom installer or video calibrator thoroughly test the HDMI video cable(s) with the entire system prior to final installation. HDMI cables vary greatly in overall quality and signal integrity. Many HDMI cables are not designed to support certain information and signal timings over long cable runs. Contact Wolf Cinema technical support and/or your cable manufacturer for additional information regarding recommended HDMI cable lengths and overall system compatibility.

3RS-232:Route and connect any 9-pin RS-232 cables from your external home automation or control system, separately to both Projector and ProScaler. These two components should be controlled independently.

X

Note: The GPIO port not used in the DCL-200FD system. It is reserved for discrete

 

 

 

 

 

 

communication protocol between the ProScaler and our DCX-series of video

 

 

 

 

 

 

projectors. Leave disconnected.

 

 

 

 

RS-232 interconnect between ProScaler and external control system

4Connect both Projector and ProScaler to AC power.

Note: Use extreme care when connecting AC Power to any products. Review the important safety notices indicated on pages 1-3 of this manual.

5Power on the two components:

ProScaler: The ProScaler will automatically turn on. If a Red LED is shown on the right side of the front panel, the scaler is receiving AC power but no video input signal is detected. If a Blue LED is shown, the scaler is receiving AC power and a good video signal has been detected. No LED indicates there is no AC power to the scaler.

If the ProScaler does not turn on automatically, depress the SCALER button on the lower left of the system remote control and then depress the green POWER ON button at the top.

Step 1 - Select the

 

Step 2 - Aim the

SCALER button to

 

remote at the

activate all the

 

ProScaler. Select the

ProScaler IR

 

green POWER ON

commands via the

 

button to turn on

remote control

 

the ProScaler

12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents ProScaler Copyright 2010 Wolf Cinema PrefaceProScalerHigh Definition Video Processor User’s Manual ProScaler ContentsAdvanced Functions Remote ControlDevice Codes Introduction Wolf Cinema’s ProScaler Basic FeaturesVideo Flexible Component Video InputsNot used Service Reset Other Rear Panel ConnectorsHdmi Before Setting Up SetupSupplied Accessories Power cords Cable Types Menu Button Press to enable on-screen System Remote Control Key ProScaler FunctionsConnect Hdmi cable from ProScaler to Projector Connecting the Projector and ProScalerAim Remote control ProScalerRemote at ProScaler IRFor 2 seconds to turn Remote at the ProjectorUsing an S-Video or a Composite Video Cable Connecting Video EquipmentConnecting Video Components with an Hdmi to Hdmi Cable ProScaler DVD player or DTV decoderPlug and Play Functions PC Connecting a ComputerMenus and User Interface Remote & MenusPicture Controls Menu OrganizationInput Select Selection Select InputZoom and Pan Zoom Control ScreenAspect Ratio Control using Menus or Remote Zoom using the Remote ControlPicture Controls Contrast Control Brightness ControlColor Saturation HueScaler Main Menu Picture Controls Detail Enhancement Detail EnhancementProScaler Enhancement Scaler Main Menu Picture Controls ProScaler EnhancementScaler Main Menu Settings Output Format Settings MenuOutput Format Input PrioritySelect Audio Output Output Connector ConditionsAssociate Audio and Video Inputs Rename InputsFactory Defaults Game ModeScaler Main Menu Settings Factory Defaults Wolf Cinema’s ProScaler Universal Remote Remote ControlPunch Through ModesProgramming the remote with the preprogrammed code MacrosProgramming a Second DVD, etc. to Other Device Buttons Press the DVD button to program the DVDs Setup Code numbersProgramming the remote with Learning Method To Erase a Learned Command From a ButtonPress one of the Macro buttons To Erase All the Learned Commands in One Device ModePress the Play button. The Device LED will blink one time Erasing the Macro CommandsFactory Reset Test Patterns Advanced FunctionsProScalerHigh Definition Video Processor User’s Manual Auto Wake Up Deinterlacer Bias ControlsAuto Standby Hot Plug Source Component InputAV Receivers and Audio Processors Device Codes137 139 052 165 115 004 124086 164 152 238Blu-ray & HD DVD CD Players Video Cassette Recorders VCR 053 012 023 039 043025 066 070 145 083 133 140 157 163 074072 056 048 101 034 012 034 039153 070AUX Media PC AUX PC & iPodAUX Lighting 247 072 251 161197 146 248 473 474 112400 177187 466457 230530 043 197 143323 328 353 354 356 457 494 070Default 139 147 126 185 085 213 277144 160 161 165 004 112 058 143 171 172Cable Boxes 020 030 111074 103 030Satellite Boxes 098 281087 111 091021 042 138 144 107001 083 095 105 035DVD-TV/DVD Combos DVD RecordersDVD-DVD/VCR Combos Wolf Cinema
Top Page Image Contents