Wolf Appliance Company DCL-200FD manual Component Input, Hot Plug Source

Page 37

ProScalerHigh Definition Video Processor User’s Manual

Component Input

Component Input menu gives you control over the analog component inputs. To use this control, you must select Component 1 or Component 2, otherwise, this menu item will be grayed out.

The Component Inputs window gives you 3 options for controlling Automatic Gain Control on Analog Inputs:

Single Sync: This is the default setting. Most component inputs will have sync on the Y signal and should use Single Sync.

Triple Sync: A few devices will add sync to all three component input signals (Y, Pb, Pr). In you know your device does this, choose Triple Sync.

AGC Disable: This choice disables Automatic Gain Control. In some cases, AGC will cause brightness levels to be incorrect due to distortions in the analog input signals. Disabling AGC may correct this problem. You probably don’t know if a device that generates an analog component signal puts sync on Y,or on all three inputs, or if it distorts the incoming signal. In general, it may be best to use Single Sync. If your picture does not look correct, experiment with the other settings.

Hot Plug Source

Hot Plug Source is a new feature that improves compatibility with certain source components that connect to the ProScaler through an HDMI input.

When Hot Plug Source is enabled for an HDMI input, a signal on the HDMI input connector, called Hot Plug, is toggled when switching to that input. Toggling Hot Plug causes the source component and ProScaler to perform an HDCP re-authentication. HDCP is a copy protection technology that is part of the HDMI standard.

Enable Hot Plug Source if you experience problems switching to a particular source component. These problems can include very slow switching with flashing on the screen, or colored noise over the entire screen. Two common components that benefit from enabling Hot Plug Source are the Sony PS3 game console and the Oppo 970 DVD player.

Hot Plug Source can be independently enabled for each HDMI input. To enable Hot Plug Source, first select an HDMI input, then select the Hot Plug Source window.

To enable Hot Plug Source, first select an HDMI input, then go to the menus to the window shown above, and select ON.

If you are unsure whether Hot Plug Source will help, then you should go ahead and enable it. The only downside to enabling Hot Plug Source is that switching could be a little slower due to the time it takes to re-authenticate.

36

Page 36 Page 38
Image 37
Page 36 Page 38
Contents ProScaler Copyright 2010 Wolf Cinema PrefaceProScalerHigh Definition Video Processor User’s Manual ProScaler ContentsAdvanced Functions Remote ControlDevice Codes Introduction Wolf Cinema’s ProScaler Basic FeaturesVideo Flexible Component Video InputsNot used Service Reset Other Rear Panel ConnectorsHdmi Before Setting Up SetupSupplied Accessories Power cords Cable Types Menu Button Press to enable on-screen System Remote Control Key ProScaler FunctionsConnect Hdmi cable from ProScaler to Projector Connecting the Projector and ProScalerAim Remote control ProScalerRemote at ProScaler IRFor 2 seconds to turn Remote at the ProjectorUsing an S-Video or a Composite Video Cable Connecting Video EquipmentConnecting Video Components with an Hdmi to Hdmi Cable ProScaler DVD player or DTV decoderPlug and Play Functions PC Connecting a ComputerMenus and User Interface Remote & MenusPicture Controls Menu OrganizationInput Select Selection Select InputZoom and Pan Zoom Control ScreenAspect Ratio Control using Menus or Remote Zoom using the Remote ControlPicture Controls Contrast Control Brightness ControlColor Saturation HueScaler Main Menu Picture Controls Detail Enhancement Detail EnhancementProScaler Enhancement Scaler Main Menu Picture Controls ProScaler EnhancementScaler Main Menu Settings Output Format Settings MenuOutput Format Input PrioritySelect Audio Output Output Connector ConditionsAssociate Audio and Video Inputs Rename InputsFactory Defaults Game ModeScaler Main Menu Settings Factory Defaults Wolf Cinema’s ProScaler Universal Remote Remote ControlPunch Through ModesProgramming the remote with the preprogrammed code MacrosProgramming a Second DVD, etc. to Other Device Buttons Press the DVD button to program the DVDs Setup Code numbersProgramming the remote with Learning Method To Erase a Learned Command From a ButtonPress one of the Macro buttons To Erase All the Learned Commands in One Device ModePress the Play button. The Device LED will blink one time Erasing the Macro CommandsFactory Reset Test Patterns Advanced FunctionsProScalerHigh Definition Video Processor User’s Manual Auto Wake Up Deinterlacer Bias ControlsAuto Standby Hot Plug Source Component InputAV Receivers and Audio Processors Device Codes137 139 052 165 115 004 124086 164 152 238Blu-ray & HD DVD CD Players Video Cassette Recorders VCR 053 012 023 039 043025 066 070 145 083 133 140 157 163 074072 056 048 101 034 012 034 039153 070AUX Media PC AUX PC & iPodAUX Lighting 247 072 251 161197 146 248 473 474 112400 177187 466457 230530 043 197 143323 328 353 354 356 457 494 070Default 139 147 126 185 085 213 277144 160 161 165 004 112 058 143 171 172Cable Boxes 020 030 111074 103 030Satellite Boxes 098 281087 111 091021 042 138 144 107001 083 095 105 035DVD-TV/DVD Combos DVD RecordersDVD-DVD/VCR Combos Wolf Cinema
Top Page Image Contents