Wolf Appliance Company DCL-200FD manual To Erase All the Learned Commands in One Device Mode

Page 31

ProScalerHigh Definition Video Processor User’s Manual

C. To Erase All the Learned Commands in One Device Mode

Step 1] Press the Source Device Input button and the ENT buttons simultaneously and hold for 3 seconds until the Device LED turns on. (The LED will stay on for 20 seconds. The next step must be entered during this period).

Step 2] Press the Source Device Input and Pause buttons simultaneously and hold for 5 seconds until the LED blinks two times.

Step 3] To exit this feature, press and hold the Source Device Input button and the ENT button simultaneously, once again. (The LED will blink three times).

3Programming the remote with Advanced Functions A. Programming Multi Commands to Macro Buttons

There are nine (7 for R5) Macro buttons (ON, System Off and 7 (5 for R5) Device buttons) that are designed to store up to 20 commands in each button.

Pressing any one of the Macro button will send out the series of commands that are stored in the button. For example, you either turn on or off several devices at a time by storing Power On/Off commands to these buttons.

Step 1] For programming Macro Commands on a Device button, press the Source Device Input and the MUTE buttons simultaneously and hold for 3 seconds until the Device LED turns on. (The LED will stay on for 20 seconds. The next step must be entered during this period).

For programming Macro Commands on the POWER ON or SYSTEM OFF button, Press the POWER ON or SYSTEM OFF button and the MUTE buttons simultaneously and hold for 3 seconds until the TV and SAT/CABLE Devices LED turns on. (The LED will stay on for 20 seconds. The next step must be entered during this period).

Step 2] Press one of the Macro buttons.

Step 3] Press in up to 20 buttons you wish to store in the Macro. (The Device LED will blink once for each button pressed).

Tip: Pressing a Device button to change device modes is considered as one command.

Step 4] Press the Channel UP button to save the selection. (The LED will blink three times to confirm the programming).

Note: You can program delays in between commands by pressing the PAUSE button. Each press add half a second to the delay.

Note: If you add the delay time at the first step of macro commands, the remote will send the macro commands once you pressed the Macro button for 2 seconds. (Press & Hold Function).

Note: You cannot program the CH + and PAUSE buttons as a macro command.

30

Page 30 Page 32
Image 31
Page 30 Page 32
Contents ProScaler Copyright 2010 Wolf Cinema PrefaceProScalerHigh Definition Video Processor User’s Manual ProScaler ContentsAdvanced Functions Remote ControlDevice Codes Introduction Wolf Cinema’s ProScaler Basic FeaturesVideo Flexible Component Video InputsNot used Service Reset Other Rear Panel ConnectorsHdmi Before Setting Up SetupSupplied Accessories Power cords Cable Types Menu Button Press to enable on-screen System Remote Control Key ProScaler FunctionsConnect Hdmi cable from ProScaler to Projector Connecting the Projector and ProScalerProScaler IR Remote control ProScalerAim Remote atFor 2 seconds to turn Remote at the ProjectorProScaler DVD player or DTV decoder Connecting Video EquipmentUsing an S-Video or a Composite Video Cable Connecting Video Components with an Hdmi to Hdmi CablePlug and Play Functions PC Connecting a ComputerMenus and User Interface Remote & MenusPicture Controls Menu OrganizationZoom Control Screen Select InputInput Select Selection Zoom and PanAspect Ratio Control using Menus or Remote Zoom using the Remote ControlPicture Controls Hue Brightness ControlContrast Control Color SaturationScaler Main Menu Picture Controls ProScaler Enhancement Detail EnhancementScaler Main Menu Picture Controls Detail Enhancement ProScaler EnhancementInput Priority Settings MenuScaler Main Menu Settings Output Format Output FormatRename Inputs Output Connector ConditionsSelect Audio Output Associate Audio and Video InputsFactory Defaults Game ModeScaler Main Menu Settings Factory Defaults Wolf Cinema’s ProScaler Universal Remote Remote ControlPunch Through ModesProgramming the remote with the preprogrammed code MacrosProgramming a Second DVD, etc. to Other Device Buttons Press the DVD button to program the DVDs Setup Code numbersProgramming the remote with Learning Method To Erase a Learned Command From a ButtonPress one of the Macro buttons To Erase All the Learned Commands in One Device ModePress the Play button. The Device LED will blink one time Erasing the Macro CommandsFactory Reset Test Patterns Advanced FunctionsProScalerHigh Definition Video Processor User’s Manual Auto Wake Up Deinterlacer Bias ControlsAuto Standby Hot Plug Source Component InputAV Receivers and Audio Processors Device Codes238 124137 139 052 165 115 004 086 164 152Blu-ray & HD DVD CD Players Video Cassette Recorders VCR 066 070 145 083 133 140 157 163 074 012 023 039 043053 025070 012 034 039072 056 048 101 034 153AUX Media PC AUX PC & iPodAUX Lighting 112 072 251 161247 197 146 248 473 474466 177400 187043 197 143 230457 530004 112 058 143 171 172 070Default 139 147 126 185 085 213 277323 328 353 354 356 457 494 144 160 161 165Cable Boxes 030 111020 030 074 103Satellite Boxes 091 281098 087 111035 107021 042 138 144 001 083 095 105DVD-TV/DVD Combos DVD RecordersDVD-DVD/VCR Combos Wolf Cinema
Top Page Image Contents