Wolf Appliance Company DCL-200FD manual Macros, Programming the remote with the preprogrammed code

Page 28

ProScaler

Macros

A Macro allows you to perform a series of button presses using a single button. Macros are useful if you find that you often repeat the same series of button presses.

For example, a Macro can be used to power up all the components in your system with a single button press.

Let’s say that find that you often pick up your remote and power up your Projector,AV Receiver, and set-top box together: this particular set of power-up button sequences is used again and again in your setup.

This series of multiple button presses could be put into a macro, so that one button selection powers up the 3 components used in this example. Note that we did not power on the Wolf Cinema’s ProScaler because it will sense a signal from the Set Top Box and it will power itself on automatically.

There are 9 buttons that can be used for Macros. They are the Power On/ Off pair, and the 7 component select buttons (AUD, BD, VCR, etc.). When you use one of these buttons for a Macro, it can no longer be used for its previous function. Therefore, the best choice for a Macro button is one that is not being used for anything else in your system.

Programming the Remote

The Wolf Cinema’s remote control has been designed to operate 6 different Audio/Video components in addition to the Projector and ProScaler. The remote control is preprogrammed to operate major brand's AUDIO, DVD, CD, VCR, SAT/CABLE and AUX (Light, Media PC etc.).

The remote control also has seven learning modes for learning the functions from the original remote controls of manufacturers.

The remote control provides distinct visual feedback with LED under the Device buttons to assist you in programming.

1 Programming the remote with the preprogrammed code

A complete listing of 3 digit codes is provided at the end of this section.

A. Using Three Digit Setup Code Number Method

Step 1] Turn on the Device you want to operate manually.

Step 2] Press the Source Device Input button and the OK buttons simultaneously and hold for 3 seconds until the Device LED turns on. (The LED will stay on for 20 seconds. The next step must be entered during this period).

Step 3] Point the remote control toward the Device and press in the first three-digit Setup Code number for that Device using the number buttons (0-9) on the remote control. (The Device LED will blink once for each button pressed).

Tip: Your Device will turn off when the corrected Setup code number has been selected. If the device does not turn off, press in the next Setup Code numbers until your device turns off.

If you have tried all of the Setup Code numbers listed and it still did not turn off, please proceed to the Auto Search Method.

Step 4] Once your Device turns off, press the Source Device Input button selected in the Step 2 once again to store the Setup Code number. (The Device LED will blink three times to confirm that the code has been stored).

Step 5] Please repeat the above steps to program the remote control for each of other devices.

27

Page 27 Page 29
Image 28
Page 27 Page 29
Contents ProScaler Preface Copyright 2010 Wolf CinemaProScalerHigh Definition Video Processor User’s Manual Contents ProScalerAdvanced Functions Remote ControlDevice Codes Wolf Cinema’s ProScaler Basic Features IntroductionFlexible Component Video Inputs VideoNot used Service Reset Other Rear Panel ConnectorsHdmi Before Setting Up SetupSupplied Accessories Power cords Cable Types System Remote Control Key ProScaler Functions Menu Button Press to enable on-screenConnecting the Projector and ProScaler Connect Hdmi cable from ProScaler to ProjectorRemote control ProScaler AimRemote at ProScaler IRRemote at the Projector For 2 seconds to turnConnecting Video Equipment Using an S-Video or a Composite Video CableConnecting Video Components with an Hdmi to Hdmi Cable ProScaler DVD player or DTV decoderConnecting a Computer Plug and Play Functions PCRemote & Menus Menus and User InterfaceMenu Organization Picture ControlsSelect Input Input Select SelectionZoom and Pan Zoom Control ScreenAspect Ratio Control using Menus or Remote Zoom using the Remote ControlPicture Controls Brightness Control Contrast ControlColor Saturation HueDetail Enhancement Scaler Main Menu Picture Controls Detail EnhancementProScaler Enhancement Scaler Main Menu Picture Controls ProScaler EnhancementSettings Menu Scaler Main Menu Settings Output FormatOutput Format Input PriorityOutput Connector Conditions Select Audio OutputAssociate Audio and Video Inputs Rename InputsFactory Defaults Game ModeScaler Main Menu Settings Factory Defaults Remote Control Wolf Cinema’s ProScaler Universal RemoteModes Punch ThroughMacros Programming the remote with the preprogrammed codePress the DVD button to program the DVDs Setup Code numbers Programming a Second DVD, etc. to Other Device ButtonsTo Erase a Learned Command From a Button Programming the remote with Learning MethodTo Erase All the Learned Commands in One Device Mode Press one of the Macro buttonsErasing the Macro Commands Press the Play button. The Device LED will blink one timeFactory Reset Advanced Functions Test PatternsProScalerHigh Definition Video Processor User’s Manual Auto Wake Up Deinterlacer Bias ControlsAuto Standby Component Input Hot Plug SourceDevice Codes AV Receivers and Audio Processors124 137 139 052 165 115 004086 164 152 238Blu-ray & HD DVD CD Players Video Cassette Recorders VCR 012 023 039 043 053025 066 070 145 083 133 140 157 163 074012 034 039 072 056 048 101 034153 070AUX Media PC AUX PC & iPodAUX Lighting 072 251 161 247197 146 248 473 474 112177 400187 466230 457530 043 197 143070Default 139 147 126 185 085 213 277 323 328 353 354 356 457 494144 160 161 165 004 112 058 143 171 172Cable Boxes 111 020 030074 103 030Satellite Boxes 281 098087 111 091107 021 042 138 144001 083 095 105 035DVD Recorders DVD-TV/DVD CombosDVD-DVD/VCR Combos Wolf Cinema
Top Page Image Contents