Sharp PN-V602 Snmp Setting, Version, Trap Setting of Authentication Error, URL Information

Page 52

Controlling the Monitor with a PC (LAN)

■ SNMP

You can configure settings related to SNMP.

SNMP SETTING

Set whether to enable or disable SNMP.

VERSION

Set the version of the SNMP to be supported.

COMMUNITY NAME 1 to 3

Set the name of the community required for the access.

USER 1 to 3

Set the user name, password, authentication method and other options required for access.

TRAP SETTING

Set whether to enable or disable the trap function.

When this function is enabled, a trap will be sent when the monitor is turned on.

TRAP SETTING OF AUTHENTICATION ERROR

Set whether the trap function sends a notification when authentication fails.

TRAP ADDRESS & PORT

Set the destination address and port number of the notification sent by the trap function.

Caution

After you set SNMP, click [Switch the main power of monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation.

If the IP address is changed while the SNMP function is operational, turn off the monitor and then turn it on again with the main power switch.

TIPS

Depending on the SNMP settings, a short delay may occur before the SNMP is usable. (About 2 minutes)

Up to 16 alphanumeric letters and symbols can be used for the community name, user name and password.

■ SERVICE & SUPPORT (URL INFORMATION)

You can display a specific URL in the URL INFORMATION field on the INFORMATION screen when an error occurs in the monitor. (See page 48.)

URL INFORMATION

Enter the URL to display on the INFORMATION screen when an error occurs on the monitor.

Up to 64 alphanumeric characters or symbols can be used.

CONDITION

Specify the condition to display the URL.

CONFIRMATION

The home page of the specified URL is displayed.

You can check whether the URL you entered is correct.

TIPS

It is also possible to specify the message text, such as the name of a contact or a telephone number, to be displayed instead of the linked URL.

E52

Image 52
Contents PN-V602 For Customers in U.K GREEN-AND-YELLOWBlue BrownRefer Servicing to Qualified Service Personnel Important InformationInformation on Disposal for Users private households Information on Disposal for Business UsersEuropean Union Other Countries outside the EUDear Sharp Customer Safety Precautions Rear side buttons Remote control unit buttons Use only the power cord supplied with the monitorFan in this product has a limited lifetime Mounting Precautions Contents Supplied ComponentsNFront view Part NamesNRear view 11 E Connecting Peripheral Equipment Connection when the PN-ZB02 optional is attachedConnecting Peripheral Equipment 13 EMultiple monitor connection Connection with video cableConnect the monitors in order Connection with the control kit optionalSet the ID No Preparing the Remote Control Unit Connecting the Power CordInstalling the batteries Remote control operation rangeBinding Cables Removing the HandlesAffixing the Protection Covers Be sure the handles are attached securelyTurning Power On/Off Turning on the main powerTurning power on/off Disabling power on/off operationsInput Input mode selection VOL +/- Volume adjustmentBasic Operation MuteBasic Operation 19 EDisplay Basic Operation NSwitching the screen size Wide Zoom NormalDot by Dot Cut offRemote Control Mode 21 EThis Monitor only Specified MonitorMenu Items Displaying the menu screenNExample of operation NMenu screen display23 E Menu item detailsNSCREEN Menu Items NPICTUREMenu Items NSETUPNAUDIO 25 E Menu Items NOPTION NMULTI 27 EMenu Items NPIP/PbyP NEnlarge Menu Items NDual screen displayPIP 29 E NZOOM2 Special SettingNSCHEDULE NAutomatic adjustment Adjustments for PC screen displayNScreen display for adjustment 31 E Communication procedure Controlling the Monitor with a PC RS-232CPC connection Communication conditions33 E NCommunication intervalNCommands for ID control Controlling the Monitor with a PC RS-232CNID numbers Advanced operation35 E NRepeater controlVOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Setting of the Gamma user data NTo transfer the Gamma user dataNSaving the Gamma user data NActivating the Gamma user dataRS-232C command table Power control/Input mode selectionHow to read the command table 37 EControlling the Monitor with a PC RS-232C Screen menu 39 E Controlling the Monitor with a PC RS-232C Picture menuSetup menu Controlling the Monitor with a PC RS-232C Audio menu41 E Controlling the Monitor with a PC RS-232C Option menuControlling the Monitor with a PC RS-232C Multi menu Image Position Epos settingHorizontal orientation Vertical orientation 43 E Initialization/Functional Restriction Setting Function menuControlling the Monitor with a PC RS-232C PIP/PbyP menu Commands for setting of the Gamma user data Controlling the Monitor with a PC RS-232C OthersSettings to connect to a LAN Controlling the Monitor with a PC LAN45 E To set on the monitorDefault Gateway 0.0 Controlling the Monitor with a PC LAN To set from a PCControlling with a PC 47 EControlling the Monitor with a PC LAN Standby mode, Power on is the operation available Information about this monitor appearsUser Name / Password 49 EDNS Server Accept IP AddressInstallation Information NAME/LOCATION AuthenticationAccount Name / Password Monitor Name51 E Recipient E-MAIL AddressesCondition ConfirmationSnmp Setting Trap SettingTrap Setting of Authentication Error VersionTroubleshooting 53 ETroubleshooting Specifications NPN-V602 Product SpecificationsNPN-ZR01 optional Product Specifications 55 ESpecifications NDimensional Drawings NPower managementNPOWER Limited See Set to ensure maximum power consumption. SeeSpecifications NCompatible signal timing PC 57 ESpecifications NCompatible signal timing AV 59 E PN-V602 Mu EN11H1
Related manuals
Manual 28 pages 8.65 Kb Manual 60 pages 10.1 Kb