BenQ LX60ST, LW61ST user manual Controls and functions

Page 10

Controls and functions

Projector

1

2

3

4

5

6

7

8

1.Focus ring

9.POWER indicator light

Lights up or flashes when the projector is under operation.

10.AUTO

9Automatically determines the best picture timings for the displayed image.

10 11.

Right/

11Increases the projector volume.

12

When the On-Screen Display (OSD)

13menu is activated, the #6, #5, and #11

5keys are used as directional arrows to select the desired menu items and to make adjustments.

Adjusts the focus of the projected image.

2.TEMPerature warning light

Lights up red if the projector's temperature becomes too high.

3.LIGHT indicator light

Indicates the status of the light source. Lights up or flashes when the light source has developed a problem.

4.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

12. POWER

Toggles the projector between standby mode and on.

13.SOURCE

Displays the source selection bar.

5.Keystone/Arrow keys ( /Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

6. Left/

Decreases the projector volume.

7.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

8.ECO BLANK

Used to hide the screen picture.

10 Introduction

Image 10

Contents LX60ST/LW61ST Table of contents Important safety instructions Safety Instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Source selection buttons COMPUTER-1, COMPUTER-2 Remote controlNetwork Setting Enters network setting directly Test Keystone/Arrow buttons / Up DownMIC/VOL + VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer Numeric buttonsReplacing the remote control batteries Remote control effective rangeOperating the projector from Front Rear Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeLW61ST Connection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus HighlightSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color3D Color Management Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Freezing the image To cancel the timer, perform the following stepsRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneSupported image formats When viewing thumbnailsPresenting from a USB Reader To view your pictures as a slide show, follow these stepsPress Power or OFF a second time. The Power indicator light Direct power offSetting Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced IP Address Wired LAN Subnet MaskDefault Gateway DNS ServerDescription of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic Function Description Quick AutoTimer SearchPanel Key AdjustmentsReceiver LockTest Pattern System Setup Advanced menu Function DescriptionBaud Rate ClosedCurrent Reset AllNetwork SystemMaintenance Care of the projectorGetting to know the light source hour Setting Light Source Mode Selection as EconomicLight source information Extending light source lifeReplacing the light source Timing of replacing the light sourceStatus Message Light Status & Description Power events IndicatorsThermal events Troubleshooting Specifications Projector specificationsWall mount installation DimensionsMinimum installation requirements Wxga Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Ceiling mount screwTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer