BenQ LX60ST Timing of replacing the light source, Replacing the light source, Status Message

Page 50

Timing of replacing the light source

When the Light indicator lights up red or a message appears suggesting it is time to replace the light source, please consult your dealer.

The following light source warning displays will remind you to change the light source.

Status

Message

Install a new light source for optimal

Notice

performance. If the projector is normally run with

 

Economic selected (See "Getting to know the

Order Replacement Light Source

light source hour" on page 49), you may continue

Light source>XXXX Hours

to operate the projector until the next hour light

 

source warning appears.

Please contact your dealer for replacing new light

 

source

Press ENTER to dismiss the message.

OK

 

 

It is strongly recommended that you replace the

Notice

light source at this age. The light source is a

 

consumable item. The light source brightness

Replace Light Source Soon

diminishes with use. This is normal light source

Light source>XXXX Hours

behavior. You can replace the light source

 

whenever you notice that the brightness level has

Please contact your dealer for replacing new light

significantly diminished.

source

 

Press ENTER to dismiss the message.

OK

 

 

Notice

 

Replace Light Source Now

 

Light source>XXXX Hours

 

Light source usage time exceeded

 

Please contact your dealer for replacing new light

 

source

 

OK

 

 

The light source MUST be replaced before the

WARNING

projector will operate normally.

 

Press ENTER to dismiss the message.

Out of Light Source Usage Time

 

 

Please contact your dealer for replacing new light

 

source

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

Replacing the light source

Do not replace the light source by yourself. Please contact your dealer.

50 Maintenance

Page 49 Page 51
Image 50
Page 49 Page 51
Contents LX60ST/LW61ST Table of contents Important safety instructions Safety Instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Source selection buttons COMPUTER-1, COMPUTER-2 Remote controlNetwork Setting Enters network setting directly Test Keystone/Arrow buttons / Up DownMIC/VOL + VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer Numeric buttonsOperating the projector from Front Rear Remote control effective rangeReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeLW61ST Connection ConnectionPlaying sound through the projector Connecting video source devicesConnecting audio About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus HighlightSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneSupported image formats When viewing thumbnailsPresenting from a USB Reader To view your pictures as a slide show, follow these stepsPress Power or OFF a second time. The Power indicator light Direct power offSetting Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced IP Address Wired LAN Subnet MaskDefault Gateway DNS ServerDescription of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic Function Description Quick AutoTimer SearchPanel Key AdjustmentsReceiver LockTest Pattern System Setup Advanced menu Function DescriptionBaud Rate ClosedCurrent Reset AllNetwork SystemMaintenance Care of the projectorGetting to know the light source hour Setting Light Source Mode Selection as EconomicLight source information Extending light source lifeStatus Message Timing of replacing the light sourceReplacing the light source Thermal events IndicatorsLight Status & Description Power events Troubleshooting Specifications Projector specificationsMinimum installation requirements DimensionsWall mount installation Wxga Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Ceiling mount screwTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer
Top Page Image Contents