BenQ LW61ST, LX60ST user manual Remote control, Source selection buttons COMPUTER-1, COMPUTER-2

Page 11

Remote control

1	13
2	13
	14
3	15
4	16
	16
5	17
6	16
	16
7	18
8	19
9	20
10	21
11	22
11
12	23
	24

1.ON/OFF

Toggles the projector between standby mode and on.

2.Source selection buttons (COMPUTER-1, COMPUTER-2,

VIDEO, S-VIDEO)

Selects an input source for display.

3.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.ECO BLANK

Used to hide the screen image.

5. Left

Decreases the projected image brightness.

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.LASER

Emits visible laser pointer light for presentation purposes.

8.PAGE UP/PAGE DOWN

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

9.FREEZE

Freezes the projected image.

10.NETWORK SETTING Enters network setting directly.

11.TEST

Displays the test pattern.

12.SMART ECO

Displays the light source mode selection bar.

13.NETWORK

Searches the network signal and project it within a few seconds once available.

14.SOURCE

Displays the source selection bar.

15.AUTO

Automatically determines the best picture timings for the displayed image.

16.Keystone/Arrow buttons ( / Up,

/ Down)

Manually corrects distorted images resulting from an angled projection.

17. Right

Increases the projected image brightness.

When the On-Screen Display (OSD) menu is activated, the #5, #16 and #17 buttons are used as directional arrows to select the desired menu items and to make adjustments.

Introduction 11

Image 11

Contents LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Keystone/Arrow buttons / Up Down Remote controlNetwork Setting Enters network setting directly Test Source selection buttons COMPUTER-1, COMPUTER-2Numeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Operating the projector from Front Rear Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsLW61ST Connection ConnectionPlaying sound through the projector Connecting video source devicesConnecting audio Device About the microphone inputStarting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Hiding the image To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeTo view your pictures as a slide show, follow these steps When viewing thumbnailsPresenting from a USB Reader Supported image formatsShutting down the projector Direct power offSetting Press Power or OFF a second time. The Power indicator lightBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced DNS Server Wired LAN Subnet MaskDefault Gateway IP AddressDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic Function Description Quick AutoTimer SettingsLock AdjustmentsReceiver Panel KeyClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternSystem Reset AllNetwork CurrentCare of the projector MaintenanceExtending light source life Setting Light Source Mode Selection as EconomicLight source information Getting to know the light source hourStatus Message Timing of replacing the light sourceReplacing the light source Thermal events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications SpecificationsMinimum installation requirements DimensionsWall mount installation Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright