BenQ LX60ST Muting the sound, Adjusting the sound level, Adjusting the microphone volume

Page 36

4.If the action is successful, you see the message 'Captured Succeeded' on the screen. The captured picture is saved as MyScreen.

5.To view the captured picture displayed as the startup screen, set MyScreen in the SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.

Using the OSD menu

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Basic menu is highlighted.

2.Press to highlight MyScreen and press MODE/ENTER.

3.Repeat steps 2-5 in the "Using the remote control" section to capture and view the captured picture.

In the unlikely event that the capturing action fails, change your target picture.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speakers. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 17 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page is displayed.

3.Highlight Mute and press / to select On.

If available, you can also press MUTE on the remote control to toggle projector audio between on and off.

Adjusting the sound level

To adjust the sound level, press VOLUME+/VOLUME- on the remote control, or:

1.Repeat steps 1-2 above.

2.Press to highlight Volume and press / to select a desired sound level.

Adjusting the microphone volume

To adjust the microphone sound level, press MIC/VOL keys (+/-) on the remote control, or:

1.Repeat steps 1-2 above.

2.Press to highlight Microphone Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2 above.

2. Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

36 Operation

Image 36
Contents LX60ST/LW61ST Table of contents Important safety instructions Safety Instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Remote control Network Setting Enters network setting directly TestSource selection buttons COMPUTER-1, COMPUTER-2 Keystone/Arrow buttons / Up DownVOLUME+/VOLUME- Adjusts the sound level Mute Operating the Laser pointerMIC/VOL + Numeric buttonsRemote control effective range Replacing the remote control batteriesOperating the projector from Front Rear Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeLW61ST Connection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector About the microphone input DeviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Using the menus HighlightUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color3D Color Management Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following steps Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneWhen viewing thumbnails Presenting from a USB ReaderSupported image formats To view your pictures as a slide show, follow these stepsDirect power off SettingPress Power or OFF a second time. The Power indicator light Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options BasicAdvanced Wired LAN Subnet Mask Default GatewayIP Address DNS ServerDescription of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function Description TeachingSystem Setup Basic Function Description Quick Auto TimerSettings SearchAdjustments ReceiverPanel Key LockSystem Setup Advanced menu Function Description Baud RateTest Pattern ClosedReset All NetworkCurrent SystemMaintenance Care of the projectorSetting Light Source Mode Selection as Economic Light source informationGetting to know the light source hour Extending light source lifeTiming of replacing the light source Replacing the light sourceStatus Message Indicators Light Status & Description Power eventsThermal events Troubleshooting Specifications Projector specificationsDimensions Wall mount installationMinimum installation requirements Wxga Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Ceiling mount screwTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Warranty and Copyright information Limited warrantyCopyright Disclaimer