BenQ LW61ST, LX60ST user manual Switching input signal, Changing Color Space

Page 27

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

1.Press SOURCE on the projector or remote control. A source selection bar is displayed.

2.Press / until your desired signal is selected and press MODE/ENTER.

If available, you can also select the source by pressing one of the Source buttons on the remote control.

Once detected, the selected source information will be displayed at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another signal.

•The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

Computer1/YPbPr1

Computer2/YPbPr2

HDMI

Video

S-Video

Network Display

USB Display

USB Reader

•For best display picture results, you should select and use an input signal which outputs at the projector’s native resolution.

Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 28 for details.

•Firewall in the PC must be switched off to allow QPresenter and USB Display to work.

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

To do this:

1.Press MENU/EXIT and then press / until the SOURCE menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI-input port is in use.

Operation 27

Image 27

Contents LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Keystone/Arrow buttons / Up Down Remote controlNetwork Setting Enters network setting directly Test Source selection buttons COMPUTER-1, COMPUTER-2Numeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Remote control effective range Replacing the remote control batteriesOperating the projector from Front Rear Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsLW61ST Connection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector Device About the microphone inputStarting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right Hiding the image To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeTo view your pictures as a slide show, follow these steps When viewing thumbnailsPresenting from a USB Reader Supported image formatsShutting down the projector Direct power offSetting Press Power or OFF a second time. The Power indicator lightBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced DNS Server Wired LAN Subnet MaskDefault Gateway IP AddressDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic Function Description Quick AutoTimer SettingsLock AdjustmentsReceiver Panel KeyClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternSystem Reset AllNetwork CurrentCare of the projector MaintenanceExtending light source life Setting Light Source Mode Selection as EconomicLight source information Getting to know the light source hourTiming of replacing the light source Replacing the light sourceStatus Message Indicators Light Status & Description Power eventsThermal events Troubleshooting Projector specifications SpecificationsDimensions Wall mount installationMinimum installation requirements Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Disclaimer Warranty and Copyright informationLimited warranty Copyright