BenQ LX60ST System Setup Advanced menu Function Description, Baud Rate, Test Pattern, Closed

Page 46

5. SYSTEM SETUP: Advanced menu

	Function	Description
		Selects a baud rate that is identical with your computer’s so that you
	Baud Rate	can connect the projector using a suitable RS-232 cable and update or
	Baud Rate	download the projector’s firmware. This function is intended for

		qualified service personnel.

	Test Pattern	Selecting On enables the function and the projector displays the grid
	Test Pattern	test pattern. It helps you adjust the image size and focus and check that
		the projected image is free from distortion.
		Closed Caption Enable
		Activates the function by selecting On when the selected input signal
		carries closed captions.
	Closed	• Captions: An on-screen display of the dialogue, narration, and
	Closed	sound effects of TV programs and videos that are closed captioned
	Caption	(usually marked as "CC" in TV listings).
		Caption Version
		Selects a preferred closed captioning mode. To view captions, select
		CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary
		language in your area).
		Network
		Selecting On enables the function. The projector is able to provide the
		network function when it is in standby mode.
		Microphone
		Selecting On enables the function. The projector can output the
		microphone signal when it is in standby mode and all the necessary
		equipment is correctly connected. See "Playing sound through the
		projector" on page 18 for details.
	Standby	Monitor Out
	Standby	Selecting On enables the function. The projector can output a VGA
	Settings	signal when it is in standby mode and the COMPUTER 1 jack is
		correctly connected to devices. See "Connection" on page 17 for how
		to make the connection.
		Audio Pass Through
		The projector can play sound when it is in standby mode and the
		corresponding jacks are correctly connected to devices. Press / to
		choose the source that you wish to use.
		See "Connection" on page 17 for how to make the connection.
		Enabling this function slightly increases the standby power consumption.

46 Operation

Image 46

Contents LX60ST/LW61ST Table of contents Important safety instructions Safety Instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Source selection buttons COMPUTER-1, COMPUTER-2 Remote controlNetwork Setting Enters network setting directly Test Keystone/Arrow buttons / Up DownMIC/VOL + VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer Numeric buttonsReplacing the remote control batteries Remote control effective rangeOperating the projector from Front Rear Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeLW61ST Connection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus HighlightSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color3D Color Management Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Freezing the image To cancel the timer, perform the following stepsRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneSupported image formats When viewing thumbnailsPresenting from a USB Reader To view your pictures as a slide show, follow these stepsPress Power or OFF a second time. The Power indicator light Direct power offSetting Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced IP Address Wired LAN Subnet MaskDefault Gateway DNS ServerDescription of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic Function Description Quick AutoTimer SearchPanel Key AdjustmentsReceiver LockTest Pattern System Setup Advanced menu Function DescriptionBaud Rate ClosedCurrent Reset AllNetwork SystemMaintenance Care of the projectorGetting to know the light source hour Setting Light Source Mode Selection as EconomicLight source information Extending light source lifeReplacing the light source Timing of replacing the light sourceStatus Message Light Status & Description Power events IndicatorsThermal events Troubleshooting Specifications Projector specificationsWall mount installation DimensionsMinimum installation requirements Wxga Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Ceiling mount screwTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer