BenQ LW61ST, LX60ST user manual Network, Reset All, Current, System, Status

Page 47

SYSTEM SETUP: Advanced me

6. INFORMATION menu

Function

Description

 

Wired LAN

 

Wireless LAN

 

Remote Desktop

 

Broadcasting

 

Projection Log In Code

Network

See BenQ Network Projector Operation Guide for details.

AMX Device Discovery

Settings

 

When AMX Device Discovery is On, the projector can be detected

 

by AMX controller.

 

Mac Address

 

Displays the mac address for this projector.

 

The System limitation of 1:1 audio is Intel Pentium 4, 3.0G CPU, 1G RAM.

 

 

 

Returns all settings to the factory preset values.

Reset All

The following settings will still remain: Phase, H. Size, User 1, User 2, Color

Settings

Space Conversion, Language, Projector Position, High Altitude

 

Mode, Security Settings, DHCP, SSID, Remote Desktop and Baud

 

Rate.

 

Source

 

Shows the current signal source.

 

Picture Mode

 

Shows the selected mode in the PICTURE menu.

Current

Resolution

Shows the native resolution of the input signal.

System

Color System

Status

Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.

 

Equivalent Light Source Hour

 

Displays the number of hours the light source has been used.

 

Firmware Version

 

Shows the firmware version of your projector.

 

 

Operation 47

Image 47
Contents LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Keystone/Arrow buttons / Up Down Remote controlNetwork Setting Enters network setting directly Test Source selection buttons COMPUTER-1, COMPUTER-2Numeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Operating the projector from Front Rear Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsLW61ST Connection ConnectionPlaying sound through the projector Connecting video source devicesConnecting audio Device About the microphone inputStarting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Hiding the image To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeTo view your pictures as a slide show, follow these steps When viewing thumbnailsPresenting from a USB Reader Supported image formatsShutting down the projector Direct power offSetting Press Power or OFF a second time. The Power indicator lightBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced DNS Server Wired LAN Subnet MaskDefault Gateway IP AddressDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic Function Description Quick AutoTimer SettingsLock AdjustmentsReceiver Panel KeyClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternSystem Reset AllNetwork CurrentCare of the projector MaintenanceExtending light source life Setting Light Source Mode Selection as EconomicLight source information Getting to know the light source hourStatus Message Timing of replacing the light sourceReplacing the light source Thermal events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications SpecificationsMinimum installation requirements DimensionsWall mount installation Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright