BenQ LX60ST, LW61ST Shutting down the projector, Direct power off, During a slide show, Setting

Page 38

During a slide show

To	Press
go to previous or next image	/

rotate the image by 90 degree clockwise/	/
rotate the image by 90 degree clockwise/	(Rotation is temporary; the image returns to
counterclockwise	its original orientation when you go back to
	thumbnails)

return to a previous page	Auto
start/stop a slide show	Enter

Setting page

You can adjust the file order and Slideshow settings. When you are done, press OK to save the settings or press Cancel to ignore the change.

Shutting down the projector

1.Press POWER or OFF, and a confirmation message will be displayed prompting you.

If you don't respond in a few seconds, the message will disappear.

2.Press POWER or OFF a second time. The POWER indicator light

flashes orange, the light source shuts down.

3. A "Power Off Ring Tone" will be heard. The POWER indicator light is a steady orange and fans stop. Disconnect the power cord from the power outlet.

• To turn off the power ring tone, see "Turning off the Power On/ Off Ring Tone" on page 36 for details.

•Light source life results will vary depending on environmental conditions and usage.

Direct power off

The AC power cord can be pulled out right after the projector is turned off.

38 Operation

Image 38

Contents LX60ST/LW61ST Table of contents Important safety instructions Safety Instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Source selection buttons COMPUTER-1, COMPUTER-2 Remote controlNetwork Setting Enters network setting directly Test Keystone/Arrow buttons / Up DownMIC/VOL + VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer Numeric buttonsOperating the projector from Front Rear Remote control effective rangeReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeLW61ST Connection ConnectionPlaying sound through the projector Connecting video source devicesConnecting audio About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus HighlightSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneSupported image formats When viewing thumbnailsPresenting from a USB Reader To view your pictures as a slide show, follow these stepsPress Power or OFF a second time. The Power indicator light Direct power offSetting Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced IP Address Wired LAN Subnet MaskDefault Gateway DNS ServerDescription of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic Function Description Quick AutoTimer SearchPanel Key AdjustmentsReceiver LockTest Pattern System Setup Advanced menu Function DescriptionBaud Rate ClosedCurrent Reset AllNetwork SystemMaintenance Care of the projectorGetting to know the light source hour Setting Light Source Mode Selection as EconomicLight source information Extending light source lifeStatus Message Timing of replacing the light sourceReplacing the light source Thermal events IndicatorsLight Status & Description Power events Troubleshooting Specifications Projector specificationsMinimum installation requirements DimensionsWall mount installation Wxga Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Ceiling mount screwTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer