BenQ LW61ST, LX60ST user manual Light source information, Getting to know the light source hour

Page 49

Light source information

Getting to know the light source hour

When the projector is in operation, the duration (in hours) of light source usage is automatically calculated by the built-in timer.

See "Setting Light Source Mode Selection as Economic" below for more information on Economic mode.

To obtain the light source hour information:

1.Press MENU/EXIT and then press / to highlight the SYSTEM SETUP: Advanced menu.

2.Press to highlight Light Source Adjustments and press MODE/ENTER. The Light Source Adjustments page is displayed.

3.You will see the Equivalent Light Source Hour information appearing on the menu.

4.To leave the menu, press MENU/EXIT.

You can also get the light source hour information on the INFORMATION menu.

Extending light source life

The light source is a consumable item that normally can last up to 10000-20000 hours with proper usage. To keep the light source life as long as possible, you can do the following settings via the OSD menu.

Setting Light Source Mode Selection as Economic

Using Economic mode reduces system noise and power consumption by 20%. If the Economic mode is selected, the light output will be reduced and result in darker projected pictures.

Setting the projector in Economic mode also extends the light source operation life. To

set Economic mode, go into the SYSTEM SETUP: Advanced > Light Source Adjustments > Light Source Mode Selection menu and press / .

Setting Auto Power Off

This function allows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of light source life.

To set Auto Power Off, go into the SYSTEM SETUP: Basic > Operation Settings

>Auto Power Off menu and press / . The time period can be set from 5 to 30 minutes in 5-minute increments. If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.

Maintenance 49

Image 49
Contents LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Network Setting Enters network setting directly Test Remote controlSource selection buttons COMPUTER-1, COMPUTER-2 Keystone/Arrow buttons / Up DownOperating the Laser pointer VOLUME+/VOLUME- Adjusts the sound level MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeOperating the projector from Front Rear Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsLW61ST Connection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector Device About the microphone inputStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Highlight Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations To cancel the timer, perform the following stepsFreezing the image Hiding the imageUsing the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring TonePresenting from a USB Reader When viewing thumbnailsSupported image formats To view your pictures as a slide show, follow these stepsSetting Direct power offPress Power or OFF a second time. The Power indicator light Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Default Gateway Wired LAN Subnet MaskIP Address DNS ServerDescription of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic Function Description Quick AutoSettings SearchReceiver AdjustmentsPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionTest Pattern ClosedNetwork Reset AllCurrent SystemCare of the projector MaintenanceLight source information Setting Light Source Mode Selection as EconomicGetting to know the light source hour Extending light source lifeReplacing the light source Timing of replacing the light sourceStatus Message Light Status & Description Power events IndicatorsThermal events Troubleshooting Projector specifications SpecificationsWall mount installation DimensionsMinimum installation requirements Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Limited warranty Warranty and Copyright informationCopyright Disclaimer